Great serviceOn 04/19/2024 by H. P. (verified customer)
Brand: Wavemaster 7000
Showing 1–30 of 43 results
-
Impeller for the Watkins Wavemaster 7000 jet pump (ver 3) This impeller screws onto the pump motor's threaded shaft with regular right-hand threads This black impeller is the replacement for the Watkins Wavemaster 7000 jet pump jet pump 1 65 HP If your ...read more -
This volute o-ring works on the Vico Ultimax version of the Watkins Wavemaster 7000 jet pump This is the large o-ring gasket that sits between the two halves (suction cover and volute) of the wet end This volute o-ring will work on the following pump model ...read more -
Sku: 36675-01DPDrain Plug, Watkins Wavemaster 7000 Jet Pump, Vico Ultimax
This drain plug works on the Vico Ultimax version of the Watkins Wavemaster 7000 jet pump Check your wet end for the "V" or your model number 36675-01 This drain plug does NOT come with the o-ring See item 36675-01RNG This drain plug will work on the ...read more -
Sku: 36675-01WRWear Ring, Watkins Wavemaster 7000 Jet Pump, Vico Ultimax
This wear ring works on the Vico Ultimax version of the Watkins Wavemaster 7000 jet pump Check your wet end for the "V" marking located on the discharge or your model number 36675-01 Only replace your wear ring if you are replacing your impeller -
This drain plug o-ring works on the Vico Ultimax version of the Watkins Wavemaster 7000 jet pump Check your wet end for the "V" marking located on the discharge or your model number 36675-01 This o-ring fits on the wet end drain plug item 36675-01DP -
This black impeller is the replacement for the Vico Ultimax version of the Watkins Wavemaster 7000 jet pump It is 1 5HP, not the OEM 1 65HP The factory no longer sells Vico replacement parts so the alternative is a new jet pump or wet end This impeller ...read more -
Sku: SK-WM-7000-V3-BYPComplete Seal Kit, Wavemaster 7000 (ver.3)
Wet End Seal Kit for the Wavemaster 7000 (ver 3) Jet Pump These parts only fit the pumps with a vendor number ending in 4081 All the replacement parts necessary when opening up the "wet end" to cure a leaking pump Since the impeller typically breaks when ...read more -
Sku: 36675-01SSShaft Seal, Watkins Wavemaster 7000 Jet Pump, Vico Ultimax
The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This shaft seal will only work with the Vico brand wet end An indicator that your Watkins Wavemaster jet pump was made by Vico is the model number will end in "-01" ...read more -
Sku: 48WUA-VWavemaster Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 48-frame LX wet ends item 77711, 77710, and 77709 Stamped on wet-end: PP-GF30; B436-14 (03) Reference models (see ...read more -
Hot Spring, Hot Spot & Solana spas only This barbed nipple screws into the front (suction cover) and is used on all Wavemaster Jet Pumps as well as the Sta-Rite 1Hp & 2Hp jet pumps on everything but Tiger River spas which use a 33732 nipple The ...read more -
Sku: 30413Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 36070-Motor-BYPMotor, 1HP, 36070 Pump
This electric motor is the energy efficient replacement motor for the Wavemaster 7000 (v 1) jet pump used on the 1993-1996 Hot Spring Classic, 1993-1995 Hot Spring Grandee and Sovereign spa models -
Sku: 70400-BYPShaft Seal, Wavemaster 7000 (v.1)
This shaft seal is for the Wavemaster 7000 (v 1) Sta-rite 5/8" shaft seal used on the 1HP and 2HP jet pumps that were built from 1998 forward This seal is used with the seal plate that DOES NOT require the copper heater sink If you are repairing a pump ...read more -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate -
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
This is the after-market 3/4" Replacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 -
Sku: 71030Shaft Seal, Wavemaster 7000 (version 2) and 9000
This item is obsolete and replaced by:
71030-BYPReplacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 See item 71030-BYP for after-market shaft seal -
Sku: 70401Impeller, 1Hp Wavemaster 7000 (v.1)
Replacement impeller for the first Wavemaster 7000 used on the 1993-1996 Hot Spring Classic, 1993-1995 Grandee, Highlife and Sovereign spa models The impeller screws onto the motor shaft (right-hand threads) This impeller does not require an impeller screw -
This slinger is for the Wavemaster 7000 version 2 and the Wavemaster 9000 If the pump's shaft seal was to begin leaking, the slinger would "sling" water off the shaft to prevent that water from migrating into the electric motor -
The diffuser mounts onto the seal plate of the Wavemaster 7000 second version and the Wavemaster 9000 jet pump using seven stainless steel screws -
Volute for the Wavemaster 7000 version 2 and the Wavemaster 9000 v 1 -
This pad goes between the motor base and the plastic base buffer against noisy motor vibrations -
Impeller screw for the Wavemaster 7000 (v 1) This screw is reversed thread (left hand thread) This screw is not needed if you are purchasing a new impeller 2014 forward -
Sku: 70408Diffuser, Wavemaster 7000 (v.1)
The diffuser screws onto the seal plate of the Wavemaster 7000 (v 1) with 3 screws which are included -
Sku: 70399Seal Plate, Wavemaster 7000 (v.1)
The seal plate is the half of the "wet end" on the 1st version Wavemaster 7000 that bolts onto the pump motor -
Seal Plate for the Wavemaster 7000 version 2 and the Wavemaster 9000 -
Jet pump motor for the Wavemaster 7000 version 2 Specs: HP: 1 0 Frame: 48Y Voltage: 115/230 Speed: 1 Amperage: 7 0/14 0 SF: 1 65 Hz: 60 Base: Steel Reference: TPEE-WK03 -
Sku: 70411Tailpiece, Wavemaster 7000 (version 1)
Inside piece of the 2" compression fitting for a Wavemaster 7000 (v 1 and v 2) and a Wavemaster 9000 -
Wavemaster 7000 (v 1) suction cover (volute) is the front half of the "wet end" (suction side) It has a square flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996 -
Sku: 70407GSKTVolute Suction Flange Gasket, Wavemaster 7000 (v.1)
Wavemaster 7000 (v 1) suction flange gasket This gasket fits between the volute cover and the square suction flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996
Showing 1–30 of 43 results