Great customer service! Called ahead to check on stock; one item was not in stock but they expected to get that week. True to expectations, they received, shipped out right away and got everything in under a week from original order. Appreciate honesty and competence and really appreciate a kind voice on the other end of the line when I called. Will definitely order from BackyardPlus again.On 12/15/2023 by J. S. (verified customer)
Showing 91–120 of 329 results
-
Sku: 71036Compression Fitting, 2in with O-Ring
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction side of most Wavemaster® XP2 or XP2e Series Jet Pumps Other compression fittings are the 71038 and 71037 ...read more -
Sku: 30237-x2-BYP
Compression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 71038
Compression Fitting, 1-1/2in with O-Ring
This 1-1/2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction and/or discharge side of FMHP/CP Series Wavemaster® Jet Pumps 2" x 1-1/2" Compression Fitting click ...read more -
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling 1-1/2" Compression Fitting 2" Compression Fitting
-
Hot Spring, Hot Spot & Solana spas only This barbed nipple screws into the front (suction cover) and is used on all Wavemaster Jet Pumps as well as the Sta-Rite 1Hp & 2Hp jet pumps on everything but Tiger River spas which use a 33732 nipple The ...read more
-
Sku: 32267-1
Drain Plug, Wavemaster
This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline For spas with a bleedline, the 32267 is used in place of this fitting This drain plug can be ...read more -
For Tiger River and Limelight spas only This 1/2" barbed adapter fitting is located on the front of Wavemaster Jet Pumps on Tiger River and Limelight spas Teflon tape should be used on the threads of this fitting for installation
-
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401
Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: 30018
Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 30413
Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 72462-BYP
Power Cord, After-Market, 1-Speed, 60″
This power cord is a 14/3 (60" long) with flag terminals on both ends The cord has three wires inside which are BLACK, WHITE, GREEN, and is used on the one-speed Jet Pumps -
Sku: 72461-BYP
Power Cord, After-Market, 2-Speed, 60″
This power cord is a 14/4 (60" long) with flag terminals on both ends The cord has four wires inside which are BLACK, RED, WHITE, GREEN and is used on the two speed Jet Pumps -
Sku: ML-1OZ-BYP
Silicone Grease, 1 oz. Tube
Silicone grease ideal for lubricating o-rings -
This after-market impeller is used on the after-market Wavemaster 9000 (ver 2), 9000 (ver 3) and Wavemaster 9200 jet pumps This 2 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads
-
This after-market impeller is used on the after-market 2 0 HP Wavemaster jet pumps This impeller screws onto the pump motor's threaded shaft with regular right-hand threads
-
This after-market impeller is used on the after-market Wavemaster 5000 and 6000 jet pumps This 1 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads
-
Sku: 71409-E
XP2E Wear Ring
This is the XP2E wear ring for the after-market impellers 71406-SW, 71405-SB and 71404-SY Please check the dots at the end of your impeller Item 71406-SW (Silver, White), item 71405-SB (Silver, Blue) and item 71404-SY (Silver, Yellow) -
Sku: 30215-Motor-BYP
1HP Starite Energy Effiecient Motor
The is the energy efficient replacement motor for the 1hp Sta-Rite pump used in some pre-1994 Hot Spring spas This motor was discontinued by Hot Spring and comes from another vendor -
Sku: 31239-Motor-BYP
Motor Only, Sta-rite 2hp
This motor replaces the two horsepower single speed energy efficient motor used on the 2HP Sta-Rite pump found on the 1989-1993 Hot Spring Highlife The "wet end" only your existing pump can be installed on this replacement motor If you require the entire ...read more -
Sku: 36070-Motor-BYP
Motor, 1HP, 36070 Pump
This electric motor is the energy efficient replacement motor for the Wavemaster 7000 (v 1) jet pump used on the 1993-1996 Hot Spring Classic, 1993-1995 Hot Spring Grandee and Sovereign spa models -
This is the largest o ring on the Wavemaster 7000 (v 1) jet pump It fits between the cover and the seal plate
-
Sku: 30217
Volute, Starite
This Sta-rite volute is the front part of the "wet end" of the 1HP and 2HP Max-E-Glas jet pumps used on the Hot Spring spa models prior to 1993 -
Sku: 30223
Impeller, 1Hp Starite
Impeller for the 1hp Sta-rite used in Hot Spring spas prior to 1993 -
Sku: 70035
Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059
Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps used on Hot Spring models prior to 1993
-
Sku: 70036
Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993
Showing 91–120 of 329 results