Best place ever, always goodOn 05/31/2024 by M. D. (verified customer)
Brand: Gliderite, Hot Spot, Hot Spring, Uprite
Showing 1–30 of 55 results
-
Sku: 72573Side Arm Assembly, Cover Cradle
This black side arm is used on the CoverCradle and the CoverCradle II It attaches to the side of the spa cover and then to the side of the spa -
Sku: 71794Gas Spring-Uprite
The Uprite® Cover Lifter employs two gas shocks that assist in opening the spa cover Sometimes these gas shocks can fall victim to the elements (storms, crazy uncles, frat parties etc ) and need replacing Replacement time is approximately thirty seconds ...read more -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
Sku: 72574Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 71095Gas Shock, Cover Cradle
Replacement 40lb gas spring shock for all models of the Cover Cradle cover lifter Gas shock color is black -
Sku: 74034Gas Shock, Cover Cradle II
Replacement 60lb gas spring shock for all Cover Cradle II cover lifters from the makers of Hot Springs spas The gas shock color is black One of these shocks is used on the Cover Cradle II -
Sku: 75103Gas Spring Lock-Uprite
The Gas Spring lock is used to secure the Uprite Lifter in the open position attaching to only one gas shock This part is typically left off when installing the Uprite Cover Lifter unless the spa is located in a windy area -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP -
This stainless steel screw secures both male and female door fasteners Used on all 1995-2009 Hot Spring spa models Price reflects a quantity of one Also used on the Hot Spring & Tiger River pre-1994 water diverter valve kit -
Sku: 72714Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
This pivot assembly is for the left side of the Cover Cradle II cover lifter as you're facing the lifter from the front This arm attaches to the side of the cover with a bracket and screws The other end attaches near the base of the spa -
Sku: 71793Angle Bracket-Uprite
Angle bracket for Uprite cover lifter -
Sku: 72572Crosslink Assembly, Cover Cradle
The Crosslink Assembly is the large "U" shaped bar that spans from the right side pivot assembly to the left side on the Cover Cradle and the Cover Cradle II cover lifter -
This pivot assembly is for the right side of the Cover Cradle II cover lifter as you're facing the lifter from the front It attaches to one side of the cover via a bracket and screws, and the other end attaches near the bottom of the edge of the spa -
This part attaches onto the right side of the spa cover -
Sku: 73451Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Right side bracket (as you are facing the spa folding the cover away from you) for the Uprite cover lifter -
Sku: 71789Upright Side Bracket Assembly, Left Side
Left side bracket (as you are facing the spa folding the cover away from you) of the Uprite cover lifter -
Sku: 75152Upright Extension Tube
One pair (quantity of two) of extensions for the Uprite cover lifter -
Sku: 71775Gliderite Base Tube Assembly, Rightside
The Gliderite has three black tubular bars (left, center and right) that fit together and form one long bar that mounts near the bottom base of the spa This tube is for the right-hand side only -
This right-side Corner Tube Assembly comes with the pivot collar and screw -
Sku: 71751Gliderite Bearing
This bearing is placed over the ¼” – 20 x 1” Hex Head Bolt -
Sku: 71750Gliderite Slide Lock Bar
The Gliderite slide lock bar is used to lock the spa cover in the vertical position in wind prone areas -
This slot tube is found on both sides of the Gliderite and connects to the opposite end of the sidearm that is attached to the spa cover Illustration (# 11) on the Gliderite parts diagram -
Sku: 71742Bolt, #10 X 2-1/2in
OBSOLETE These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite Illustration (# 5) on the Gliderite parts diagram -
Sku: 75150Uprite Channel Pivot Assembly, Left Side
This part attaches onto the left side of the spa cover -
Sku: 72571Cover Cradle Left Side Pivot Assembly
The left side pivot assembly viewed standing behind the Cover Cradle -
Sku: 72570Cover Cradle Right Side Pivot Assembly
The right side pivot assembly viewed standing behind the Cover Cradle -
Sku: 72715Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
Sku: 71744Washer, Gliderite
These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter
Showing 1–30 of 55 results