Backyardplus is awesome! I received technical help on the phone to find the part I needed. The cost was very reasonable, and the part was shipped to me without delay. ThanksOn 10/03/2024 by T. G. (verified customer)
Showing 1–30 of 68 results
-
This repair kit for the Watkins No Fault heater includes the replacement end cap for the double barrel PDR heaters which fits the Watkins Manufacturing label only This kit comes with two red seals/o-ring gaskets, replacement screws, 2 side braces and the ...read more -
Heater connection wire kit, 8" long, 10 gauge wire, qty of 2 Connects from Hot Spot heater to board of S-Class series control box -
Grounding bar for the Hot Spot heater (after-market Gecko S-Class) 5 Position, 14-6 AWG This grounding bar is attached to the heater on Hot Spot and Solana brand spas and allows the pump and other accessories to have a secondary ground tied into the ...read more -
Pipe thread sealant used with installing pressure switches Enriched with PTFE, it is non-hardening, immediate pressurization, lead free, and for plastic and metal pipe Seals and lubricates threaded connection on metal and plastics Formulated for potable ...read more -
This Hot Spot heater electronic pressure switch is a safety device that will shut down the heater if a "low water flow" condition occurs It is used on Hot Spot models (except Sprint & Dash models) and Solana spa models Some symptoms of failure include ...read more -
Sku: 31212O-Ring, Heaterbody 115V 1.5Kw
This o-ring is used to seal the heater element (31255) into the heater housing(s) (part 10475 or 30786) -
Sku: 70108Retainer Gasket, Heaterbody 115V
The Retainer is used to hold the Heaterbody O-ring, (31212) into place on Hot Spring models only -
NOTE: It is recommended to buy the OEM O-Ring (31212) and Gasket (70108) The ones included are slightly thinner than the OEM This 1500 watt heater element is the replacement for all 1980-1994 Hot Spring spa models that operated on 115volts This heater ...read more -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more -
Sku: 70868-BYPInsulation, Heaterbody 115V
This is an alternate version of the OEM insulation which minimizes the heat loss through the heater housing The insulation is wrapped around the stainless steel heater body used in 115 volt spas made from 1980 to 1994 -
Sku: 1594901-1Manifold Plug, 3/4in Ribbed Plug Manifold
This plug can be used with manifold 010017 to plug up any unused water lines -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit -
Sku: 30348Screw, #10-24 X 3/4in Stainless Steel
Stainless steel screw mostly used on the 1980-1994 115volt Hot Spring heaters to secure the heater element to the heater body Four of these are used with each heater -
Sku: 30392Nut, Hex #10-24in Stainless Steel
Used on the 1980-1994 115volt Hot Spring heaters in conjunction with the stainless steel screw (30348) to secure the heater element to the heater body -
Sku: 31409-BYPHeater Element, Hot Spring, 230v 2.5kW, Pre-1995
What's Included: Heater element w/ power cord, gasket and o-ring This 230v heater element was used on the 1987-1994 Hot Spring Grandee, Highlife and 230-volt Classic and Indoor/Outdoor (later named Sovereign) models There are two heater elements located ...read more -
Stainless steel screw used to secure the heater to the equipment compartment floor on Hot Spring & Tiger River spa models Also used on the SilentFlo 5000 Circulation pump and to hold the Ozonator to the wall of the equipment compartment -
This replacement compression fitting split nut (AKA Split Union Nut-2") is used to connect heaters on the 1993-1994 Hot Spot Z, all 1998-current Hot Spot models, Solana models beginning in 2000 and all 1992-1994 Tiger River spas It is designed in two half ...read more -
Sku: 3124070092O-Ring With Retainer Gasket, Heaterbody 230V
This o-ring and retainer gasket is used to seal the heater element (part 31409-BYP) with 2" x 4" flange into the heater housing (part 70192) -
Sku: 30396Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 34877O-Ring, Heater Flange, Cartridge Heater
One of two o-rings used to seal the cartridge-style heater to its flange on all 1995-1996 Hot Spring & Tiger River spas and 1995-1997 Hot Spot spa models The second o-ring is a 34876 -
One of two o-rings used to seal the cartridge-style heater to the flange on all 1995-1996 Hot Spring & Tiger River spas and 1995-1997 Hot Spot spa models The other o-ring is a 34877 -
Sku: 10475-BYPHeaterbody, Hot Spring, 115V, 3/4in Ports
What's Included: Heaterbody, 115V -Stainless Steel with two 3/4" ports and one 1/4" port Description: Stainless steel heater housings with 3/4 inch ports were used on all 1990-1994 115v Hot Spring spa models The housing (heater body) is tubular in shape ...read more -
Sku: 70905Heater Tailpiece, Hot Spot and Solana
This heater tailpiece glues into the plumbing on one end and the threaded end is coupled with the compression nut of the heater on a 1993-1994 Hot Spot Z, all 1998-2002 Hot Spot models, and all 2000-current Solana spa models The heaters have a compression ...read more -
Sku: 30620Insulation, Heaterbody, 230V
The insulation surrounds the heater housing found on all 220 volt Hot Spring Spas manufactured from 1984-1994 This insulation minimizes the heat loss through the heater housing -
Gasket for 2 inch Flow Thru heater for Hot Spot models This item is a 2-pack and comes with 2 gaskets -
Sku: 70732Discharge, Heater -Tiger River
This adapter is located between the heater and jet pump on a 1992-1994 Tiger River Khyber, Manora, and Tondi spa and connects onto the small circulation pump (usually the Silentflo 5000) via a 1/2" vinyl tube -
Used on the 1995-1997 Hot Spot spas this fitting provided a flange for the cartridge-style heater element to seal against and a "dry-well" for the thermistor probe to slide into -
Sku: 20305Heater Screws, package of 4
This kit contains four machine screws with phillips heads and four nuts that fit the machine screws These screws and nuts are used for the heaters used on the 110 volt model Hot Springs spas made from 1980 to 1994 -
Sku: 71539Heater Cord Adapter, 230v Tiger River
This heater cord adapter may be needed when replacing a No-Fault 5500 cartridge heater with a new PDR Heater Assembly in a 1995-1996 Tiger River 230volt wired spa model This adapter is attached to the end of the new PDR heater's power cord to enable it to ...read more -
Sku: 71538Heater Cord Adapter, 115v Tiger River
This heater cord adapter may be needed when replacing a No-Fault 1500 cartridge heater with a new PDR Heater Assembly in a 1995-1996 Tiger River Manora or Tondi spa model This adapter is attached to the end of the new PDR heater's power cord to enable it to ...read more
Showing 1–30 of 68 results