Excellent to work with, as usual. My "go to" resource for anything to do with my Hot Springs spa!On 06/28/2022 by (verified customer)
Get Watkins Wavemaster Pumps, Circulation Pumps, Wet-end Kits, Impellers, Shaft Seals, O-rings, Compression Fittings, and other parts related to your pumps.
Showing 1–30 of 319 results
-
Sku: 7769K84-1
Noninsulated 90 Degree Flag Quick-Disconnect Terminals for 16-14 Wire Gauge, 0.25″ Wide x 0.032″ Thick Tab
Non-insulated 90° Flag Quick-Disconnect Terminal for 16-14 gauge wire used on circulation and jet pump power cords -
Sku: 7769K82
Noninsulated 90 Degree Flag Quick-Disconnect Terminals for 22-18 Wire Gauge, 0.25″ Wide x 0.032″ Thick Tab
Non-insulated 90° Flag Quick-Disconnect Terminal for 22-18 gauge wire used on circulation and jet pump power cords -
Sku: 69405K54-1
Noninsulated High-Temperature Ring Terminals; 900 Degree F Maximum Temperature, for 16-14 Gauge and Number 10 Screw
Non-insulated Ring Terminals, for 16-14 Gauge used to ground pump power cords -
Sku: 69405K51
Noninsulated High-Temperature Ring Terminals; 900 Degree F Maximum Temperature, for 22-18 Gauge and Number 10 Screw
Non-insulated Ring Terminals, for 22-18 Gauge used to ground pump power cords -
This is the complete circulation pump retrofit kit for Hot Spot SX tubs beginning in 2020 and Hot Spot TX tubs beginning in 2021 What's included:Â A Frog Bypass Assembly B Circulation Pump to Heater Inlet Assembly B1 2" Heater Inlet Conector with ...read more
-
What's Included: E5 Circulation Pump with power cord Description: This SilentFlo E5 circ pump replaces all previous versions of single-speed and two-speed circulation pumps The new E5 replaces the Watkins SilentFlo® 5000 and all previous ...read more
-
Sku: 71447-BYP
Shaft Seal Kit, Wavemaster
The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This seal kit is used on most of the Wavemaster and after-market jet pumps Please find your pump model number and if your pump is an OEM Wavemaster, you will also ...read more -
Sku: 71409
Wear Ring, Wavemaster
The jet pump wear ring keeps water from back flowing around the impeller which would reduce the jet pressure significantly It fits inside the "wet end" and slides over the impeller with the ridge side farthest away from the front of the impeller (i e , ...read more -
Sku: 71409-E
XP2E Wear Ring
This is the XP2E wear ring for the after-market impellers 71406-SW, 71405-SB and 71404-SY Please check the dots at the end of your impeller Item 71406-SW (Silver, White), item 71405-SB (Silver, Blue) and item 71404-SY (Silver, Yellow) -
Sku: ML-1OZ-BYP
Silicone Grease, 1 oz. Tube
Silicone grease ideal for lubricating o-rings -
Sku: 77363
Shaft Seal Jet Pump #3536
The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This seal kit is used on most of the Wavemaster and after-market jet pumps Please find your pump model number and if your pump is an OEM Wavemaster, you will also ...read more -
Sku: 56WUA500-V
Wavemaster 9000/9200, 8000/8200 Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 56-frame LX wet ends item 77713 and 77712 -
Sku: 71554
Wavemaster Volute O-Ring
GECKO MODEL O-RING Replacement o ring (largest o-ring) for the Wavemaster 4000, 6000, 8000 (ver 3), 8200, 9000 (ver 3), 9200 jet pumps Will fit on pump series: XP2/XP2e -
Sku: 48WUA-V
Wavemaster Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 48-frame LX wet ends item 77711, 77710, and 77709 Stamped on wet-end: PP-GF30; B436-14 (03) Reference models (see ...read more -
Sku: 71410-BYP
Volute O-Ring, Wavemaster
This is the largest O-ring used on the current Wavemaster series of wet ends for Hot Springs, Tiger River, Limelight, Solana and Hot Spot model spas This o-ring fits between the suction cover and the volute of the pump series: XP2/XP2E This o-ring is only ...read more -
This is the complete "Wet End" of the Wavemaster 7000 1 65hp, 48 Frame jet pump The jet pump is comprised of two main components: the electric motor and the "Wet End" Please verify your pump's model number and vendor code when selecting replacement parts
-
Pre-wired 120volt replacement for the third version of the Wavemaster® 7000 and it's a 1 65 horsepower single-speed jet pump
-
This o-ring fits onto the front of the diffuser on the Wavemaster 7000 (v 1) jet pump and also between the suction flange and the suction cover on the front of the pump
-
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more
-
This is the largest o ring on the Wavemaster 7000 (v 1) jet pump It fits between the cover and the seal plate
-
Sku: 72196-BYP
Jet Pump, 2.5HP, 48-Frame, 1-Speed, 230V, 10.0A
This is the 2 5 HP dual speed After-Market version (but wired for single-speed) of the Wavemaster® 9000 jet pump which can be found on the Hot Spring, Tiger River, Limelight, and Hot Spot brand spas NO VENT SHROUD 2 5 HP (Operational horsepower), Dual ...read more -
Sku: 72196
Pump, Wavemaster 9000
This 2 5HP single-speed Wavemaster 9000 is the second version Wavemaster 9000 jet pump and is found on the Hot Spring, Tiger River, Limelight and Hot Spot brand spas Also included is the bleedline nipple (item 32267) -
This is the AFTER-MARKET "wet end" of the jet pump Your Wavemaster 8000, 2 0 HP jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire "wet end kit" is needed Perfect remedy if your "wet end" has ...read more
-
This is the AFTER-MARKET "wet end" of the jet pump Your Wavemaster 9000 & 9200 (v 2), 2 5 HP jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire "wet end kit" is needed Perfect remedy if your ...read more
-
This is the AFTER-MARKET "wet end" for the 1 0HP FMCP pump The intake and discharge measure 1-1/2" This "wet end" will attach to your existing motor Your jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, ...read more
-
This is the AFTER-MARKET "wet end" for the 1 0HP pump The intake and discharge measure 2" This "wet end" will attach to your existing motor Your jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire ...read more
-
This is the AFTER-MARKET "wet end" for the 1 5HP FMHP pump The intake and discharge measure 1-1/2" This "wet end" will attach to your existing motor Your jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, ...read more
-
This is the complete "wet end" of the jet pump Your Wavemaster 9000 & 9200 (v 2), 2 5 HP jet pump is comprised of two main components: the electric motor and the "wet end" In some cases, this entire "wet end kit" is needed Perfect remedy if your "wet ...read more
-
Sku: 30220
Volute O-Ring, Starite
Volute O-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993 -
Sku: 72197
Pump, Wavemaster 8200
This Wavemaster® 8200 Jet Pump is found on select years of the Hot Spring Envoy, Aria, Grandee and the Tiger River Caspian spa models This Pump is also one of two pump models found on all Limelight Glow, Flash, & Flair spa models Also included is the ...read more
Showing 1–30 of 319 results