First time buying from here and will definitely do it againOn 09/09/2018 by D. A. (verified customer)
Showing 1–30 of 385 results
-
Item #: 69405K51Noninsulated High-Temperature Ring Terminals; 900 Degree F Maximum Temperature, for 22-18 Gauge and Number 10 Screw
Non-insulated Ring Terminals, for 22-18 Gauge used to ground pump power cords -
Item #: 7769K84-1
Noninsulated 90 Degree Flag Quick-Disconnect Terminals for 16-14 Wire Gauge, 0.25″ Wide x 0.032″ Thick Tab
Non-insulated 90° Flag Quick-Disconnect Terminal for 16-14 gauge wire used on circulation and jet pump power cords -
Item #: 69405K54-1
Noninsulated High-Temperature Ring Terminals; 900 Degree F Maximum Temperature, for 16-14 Gauge and Number 10 Screw
Non-insulated Ring Terminals, for 16-14 Gauge used to ground pump power cords -
Item #: 7769K82
Noninsulated 90 Degree Flag Quick-Disconnect Terminals for 22-18 Wire Gauge, 0.25″ Wide x 0.032″ Thick Tab
Non-insulated 90° Flag Quick-Disconnect Terminal for 22-18 gauge wire used on circulation and jet pump power cords -
Item #: 300055
Spring Clamp, 3/4 inch
3/4" spring clamp (aka wire clamp) is used to secure the 3/4 inch vinyl tubing (70315) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to ...read more -
Item #: 73019
Pillow Retainer Screw Kit
The plastic retainers in this kit come in two lengths: The short gray retainers are used if your pillows have remained in place over the years The gray extensions are used only if your pillows have fallen off often in the past -
Item #: 34878
O-Ring, Control Thermistor
Control Thermostat Thermistor o-ring for the 79006 and 78970 thermistors This o-ring is located on the "inlet" side of the heater and is the larger of the two thermistor o-rings For the outlet side of the heater see the part# 34879Â o-ring -
Item #: 73223-Screw-BYP
Screw, Front Cover of IQ 2020 Control Box
Screw, Front Cover of IQ 2020 Control Box (THPH SS 8-32X3/8') -
Item #: 34879
O-Ring, Hi-Limit Thermistor
High-Limit Thermistor o-ring for the 79005 and 78969 thermistors This o-ring is located on the "outlet" side of the heater and is the smaller of the two thermistor o-rings For the "inlet" side of the heater see part 34878 -
Item #: 31134
Spring Clamp, 1/4in
Used to secure 1/4" vinyl tubing to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this spring clamp onto the vinyl tubing -
Item #: 37112
O-Ring, Precision Jet
Precision Jet o-ring fits between the interior spa shell and the wall fitting nut to prevent leaks from around the jet  The o-ring creates a seal between the jet body and the back of the shell when compressed by the wall fitting nut -
Item #: 36534
Gasket, Jet Face
This black rectangle rubber gasket fits inside of the jet face on Hot Spring, Tiger River, Hot Spot, and Solana spa models  This gasket creates the seal for the air adjustment of the jet  This gasket failing will not cause the spa to leak -
Item #: 35986
O-Ring, Adj/Jet Small, Hot Spring
Small o-ring used on various jets -
Wall fitting nut o-ring
-
Item #: 71554
Wavemaster Volute O-Ring
GECKO MODEL O-RING Replacement o ring (largest o-ring) for the Wavemaster 4000, 6000, 8000 (ver 3), 8200, 9000 (ver 3), 9200 jet pumps Will fit on pump series: XP2/XP2e -
Item #: 56WUA500-V
Wavemaster 9000/9200, 8000/8200 Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 56-frame LX wet ends item 77713 and 77712 -
Item #: 48WUA-V
Wavemaster Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 48-frame LX wet ends item 77711, 77710, and 77709 Stamped on wet-end: PP-GF30; B436-14 (03) Reference models (see ...read more -
This stainless steel screw is used to secure the Moto-Massage faceplate to its guide body on many Hot Spring and Solana spa models  Also used on the 1995-1999 Hot Spring Dream Pillow Jet  Check your serial number in the parts finder to be sure this part ...read more
-
Item #: 10437
O-Ring, Wall Fitting
Silicone (rubber will break down in chlorinated water) o-ring to seal the wall fitting nut against the spa shell The wall fitting nut screws into the jet body that's located on the back of the spa shell -
Item #: 71410-BYP
Volute O-Ring, Wavemaster
This is the largest O-ring used on the current Wavemaster series of wet ends for Hot Springs, Tiger River, Limelight, Solana and Hot Spot model spas This o-ring fits between the suction cover and the volute of the pump series: XP2/XP2E This o-ring is only ...read more -
Item #: 31228
Spring Clamp, 1/2in
1/2" spring clamp for securing 1/2" vinyl tubing to components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers are hose clamp pliers to squeeze then slide this spring clamp onto the ...read more -
This o-ring fits onto the front of the diffuser on the Wavemaster 7000 (v 1) jet pump and also between the suction flange and the suction cover on the front of the pump
-
Item #: 33850
Screw, 8-16 X 1/2in
This screw is used on various air controls and water diverter valve levers & bezels -
Item #: 34465
Spring Clamp, 3/8in
3/8" spring clamp (aka wire clamp) is used to secure the 3/8 inch vinyl tubing to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers are hose clamp pliers to squeeze then ...read more -
Item #: 71107-BYP
Ball Stud, Cover Lifters, 1/4in Threaded Shaft (Qty of 1)
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
Item #: 70405
Suction Cover O-Ring, Wavemaster 7000 (v.1)
This is the largest o ring on the Wavemaster 7000 (v 1) jet pump It fits between the cover and the seal plate -
Item #: 30348
Screw, #10-24 X 3/4in Stainless Steel
Stainless steel screw mostly used on the 1980-1994 115volt Hot Spring heaters to secure the heater element to the heater body  Four of these are used with each heater -
Item #: 30220
Volute O-Ring, Starite
Volute O-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993 -
Item #: 72574
Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Item #: 77290
Panel Clip, Door/side, NXT
Door and side panel clip NXT model Highlife Collection  Grandee NXT (GGN), Envoy NXT (KKN), JetsetterNXT (JJN)  To remove Door/Side Panel, loosen the 2 screws on each clip below the panel  Slide Door/Side Panel to the "LEFT"  Door/Panel will drop ...read more
Showing 1–30 of 385 results