It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Brand: Clarion Light, Iq 2000, Starite, Wavemaster 6000, Wavemaster 9200
Showing all 17 results
-
Sku: 31134Spring Clamp, 1/4in
Used to secure 1/4" (ID) vinyl tubing 70318 (OD measure 7/16") to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this ...read more -
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 30413Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 70035Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70036Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 30297Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Sku: 30220Volute O-Ring, Starite
Volute O-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993 -
This screw is used to hold the front cover of the IQ 2000 and IQ 2020 box in place This screw is not compatible on models made between 2007 and 2009 5 or older models with the upgraded heater relay board (Item #77119) The screw is too long and will hit ...read more -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment -
Sku: 73256Clarion Brackets
These brackets are used to mount the Clarion Light Bars to the spa or step or where ever desired Five sets of left and right pairs are included in each pack -
This diffuser lock washer is used with the screws and nuts that belong to heater 20286 50-BYP and 20286 75-BYP -
Sku: 56WUA500-VWavemaster 9000/9200, 8000/8200 Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 56-frame LX wet ends item 77713 and 77712 -
Sku: 48WUA-V
Wavemaster Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 48-frame LX wet ends item 77711, 77710, and 77709 Stamped on wet-end: PP-GF30; B436-14 (03) Reference models (see ...read more -
Sku: 73163Clarion Hardware Bag
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This hardware bag contains all of the hardware necessary to mount five Clarion Light Bars It does not ...read more
Showing all 17 results