quick ship ,as described and was perfect transaction. ThanksOn 06/13/2024 by B. H. (verified customer)
Brand: Gliderite, Iq 2000, Uprite, Wavemaster 7000
Showing all 27 results
-
Sku: 30413Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate -
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
This screw is used to hold the front cover of the IQ 2000 and IQ 2020 box in place This screw is not compatible on models made between 2007 and 2009 5 or older models with the upgraded heater relay board (Item #77119) The screw is too long and will hit ...read more -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP -
Impeller screw for the Wavemaster 7000 (v 1) This screw is reversed thread (left hand thread) This screw is not needed if you are purchasing a new impeller 2014 forward -
Sku: 73451Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Sku: 71751Gliderite Bearing
This bearing is placed over the ¼” – 20 x 1” Hex Head Bolt -
Sku: 71742Bolt, #10 X 2-1/2in
OBSOLETE These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite Illustration (# 5) on the Gliderite parts diagram -
Sku: 71744Washer, Gliderite
These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter -
Sku: 71217Hex Head Bolt, 1/4in-#20 X 1in
This bolt is used to fasten the Slide Lock Bar to the Side Arm -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor -
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1) -
Sku: 71218Bolt, #20 X 1/4in. X 2in. Hex Head
Attaches the sidearm to the pivot wheel on all spa models (except the Hot Spring Classic) -
Sku: 75105Hardware Bag #4 for Upright Cover Lifter
Hardware for the upright spa cover lifter -
Sku: 48WUA-VWavemaster Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 48-frame LX wet ends item 77711, 77710, and 77709 Stamped on wet-end: PP-GF30; B436-14 (03) Reference models (see ...read more -
Sku: 70404Diffuser Screw, 8-32 X 1in Phillips, Wavemaster 7000 V1
This item is obsolete and replaced by:
70951Obsolete: Factory replacement suggestion item 70951 This is the screw that secures the diffuser to the seal plate on a Wavemaster 7000 (v 1) pump -
Sku: 71105Bracket, Corner (G/K)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Bracket, Corner (G/K) -
Sku: 72452Side Hinge, 11/16in Base with Screw
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This side hinge screws into the vinyl cover and is used on the Gliderite & Cover Cradle cover lifters ...read more -
OBSOLETE-Use the 71107-BYP -
Sku: 71215Screw, 1/4-20 x 3/4in for Side Hinge
Obsolete from the factory -Available at most hardware stores This #20 1/4in x 3/4" standard screw (stainless steel) that secures the sidearm to the base hinge -
Sku: 71110Screw, #10 X 1-1/2in
Obsolete from the factory -Available at most hardware stores 1-1/2in Phillips flat head screw that attaches the side hinge base to the spa cover -
Sku: 71109Screw, #10 X 1/2in, Pan Head
Obsolete from the factory - Available at most hardware stores Screw, #10 X 1/2in, Pan Head This Phillips Head screw is used on various cover lifter models -
Sku: 71216Screw, 1/4in X #20 Hinge Rear
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com -
OBSOLETE- USE 30396
Showing all 27 results