The team at Backyardplus.com are the best for anything Hot Springs. Super friendly and knowledgeable.On 06/05/2024 by S. O. (verified customer)
Brand: Hot Spring | Hardware: Bracket, Clip, Screw
Showing 1–30 of 56 results
-
This stainless steel screw is used to secure the Moto-Massage faceplate to its guide body on many Hot Spring and Solana spa models Also used on the 1995-1999 Hot Spring Dream Pillow Jet Check your serial number in the parts finder to be sure this part ...read more -
GECKO MODEL SCREW This stainless steel screw is used to attach the volute cover to the volute on most Wavemaster jet pumps -
Sku: 70036Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 33850Screw, 8-16 X 1/2in
This screw is used on various air controls and water diverter valve levers & bezels -
Sku: 77290Panel Clip, Door/side, NXT
Door and side panel clip NXT model Highlife Collection Grandee NXT (GGN), Envoy NXT (KKN), JetsetterNXT (JJN) To remove Door/Side Panel, loosen the 2 screws on each clip below the panel Slide Door/Side Panel to the "LEFT" Door/Panel will drop ...read more -
Sku: 302637Door Screw, Hot Spot
This screw is used to attach the door(s) on all Hot Spot spas beginning in 2003 that use wood or synthetic wood siding: 1/4-20 x 1-3/4" Truss stainless steel Phillips head screw Price is per individual screw This part number replaces the obsolete 1-1/2" ...read more -
Sku: 30356Nylon Screw, Control Panel, Hot Spring
Nylon screw used to secure the control panel (70275) in place on all 1989-1993 Hot Spring spa models The nylon screw threads into the actual control box so it is critical to use a non-conductive material to prevent an electrical short in the control box from ...read more -
Stainless steel screw used to secure the heater to the equipment compartment floor on Hot Spring & Tiger River spa models Also used on the SilentFlo 5000 Circulation pump and to hold the Ozonator to the wall of the equipment compartment -
This screw is used to hold the front cover of the IQ 2000 and IQ 2020 box in place This screw is not compatible on models made between 2007 and 2009 5 or older models with the upgraded heater relay board (Item #77119) The screw is too long and will hit ...read more -
Sku: 30334Screw, #4 X 1/2in Stainless Steel
Stainless steel screw used in various locations on Hot Spring, Tiger River, Solana, Hot Spot and Limelight spas -
Sku: 30343Screw, #8 X 7/8in
Stainless steel screw for the jet selector water diverter valve lever on all Hot Spring spa models manufactured prior to 1994 that have a jet selector -
Sku: 30344Screw, #8 X 1in Stainless Steel
Stainless steel screw, #8 x 1in, used on the air control lever of Hot SPring models from 1989-1993 -
Sku: 36586Clip, Extruded Air Valve
Used to hold the air intake for the Freshwater II Ozonator in place on the wall in the equipment compartment near the Ozonator Found in Hotspring and Tiger River Spas with Freshwater II Ozonators -
Impeller screw for the Wavemaster 7000 (v 1) This screw is reversed thread (left hand thread) This screw is not needed if you are purchasing a new impeller 2014 forward -
Sku: 37262Mounting Screw, Control Panel
Two of these screws are used to hold the control panel assembly to the spa These screws are hidden by the frosted light cover that is found at the top of the control panel bezel -
Sku: 70945Gasket, Impeller Screw Wavemaster 9000
This little gasket fits over the impeller screw and is snugged into place against the impeller when the screw is tightened -
Four of these stainless steel screws are used to mount the control head (the electronic part of the control panel) to the control panel bezel These are accessible from behind the control head -
Sku: 73249Panel Clips, Male and Female, QTY 4
Panel clips, male/female, for the removable panels on Hot Spring models, quantity of 4 -
This stainless steel impeller screw (left-hand threads) screws onto the end of the motor shaft to secure the impeller from spinning off of the Sta-rite Maxi-Glass 1hp & 2hp pumps that were used in Hot Spring spas prior to 1994 -
Sku: 34363Screw,#10-32 X 1-1/2in
This gray-colored tipped 1-1/2" long screw secures the control panel in place on all 1994-1997 wood-sided Hot Spring models and is also found in various other locations such as the Dream Pillow etc -
Sku: 70191Screw, Drain Slide 1-1/4in
Drain slide screw, 1-1/4" -
Sku: 2317
Screw, #10 x 1/2″
Stainless steel screw -
Sku: 30347Screw, #10-24 X 1/2in Stainless Steel
Stainless steel screw -
This screw is used for holding the IQ 2000 and IQ 2020 control boxes in place on the mounting bracket in Hotsprings, Tiger River, and Limelight spas -
Sku: 36018IQ Control Box Bracket
This aluminum bracket attaches to the spa door frame to enable the IQ Control Box to mount securely to this bracket The bracket does not come with the two 36898 screws that attach it to the control box Simple wood screws are used to attach it to the wood ...read more -
This screw was used to hold the thermostat knob in place on the topside control panel used on Tiger River spas from 1992 to 1994 and the round-shaped air control knob on air valves used on Hotspring spas from 1989 to 1993 5 -
Sku: 70946Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Door screws in Mocha color for Highlife spas beginning in 2014 Set of six -
Sku: 73256Clarion Brackets
These brackets are used to mount the Clarion Light Bars to the spa or step or where ever desired Five sets of left and right pairs are included in each pack -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor
Showing 1–30 of 56 results