On 06/12/2024 by S. W. (verified customer)
Brand: Iq 2020, Uprite, Wavemaster 8000, Wavemaster 9000
Showing all 18 results
-
Sku: 73223-Screw-BYPScrew, Front Cover of IQ 2020 Control Box
Screw, Front Cover of IQ 2020 Control Box (THPH SS 8-32X3/8') -
Sku: 30413Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
Sku: 30099Bushing, Strain Relief
This 3/8" strain relief is used to secure the jet pump(s), circulation pump, light and Ozonator power cords to the bottom of the IQ 2020 Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should ...read more -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP -
Sku: 70945Gasket, Impeller Screw Wavemaster 9000
This little gasket fits over the impeller screw and is snugged into place against the impeller when the screw is tightened -
Sku: 73451Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Sku: 70946Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Sku: 71744Washer, Gliderite
These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor -
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump -
This screw is used to secure the volute to the pump base 70959 -
Sku: 75105Hardware Bag #4 for Upright Cover Lifter
Hardware for the upright spa cover lifter -
Sku: 56WUA500-VWavemaster 9000/9200, 8000/8200 Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 56-frame LX wet ends item 77713 and 77712 -
Sku: 71105Bracket, Corner (G/K)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Bracket, Corner (G/K) -
OBSOLETE-Use the 71107-BYP -
Sku: 71110Screw, #10 X 1-1/2in
Obsolete from the factory -Available at most hardware stores 1-1/2in Phillips flat head screw that attaches the side hinge base to the spa cover -
Sku: 71109Screw, #10 X 1/2in, Pan Head
Obsolete from the factory - Available at most hardware stores Screw, #10 X 1/2in, Pan Head This Phillips Head screw is used on various cover lifter models
Showing all 18 results