I have always found the Backyard Plus sales representatives to be knowledgeable and helpful. The prices are great. This is my go to place for my hot tub.On 05/29/2024 by D. F. (verified customer)
Brand: Tiger River | Hardware: Clamp, Plug, Screw
Showing all 24 results
-
Sku: 300055Spring Clamp, 3/4 inch
3/4" spring clamp (aka wire clamp) is used to secure the 3/4 inch vinyl tubing (70315) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to ...read more -
Sku: 31134Spring Clamp, 1/4in
Used to secure 1/4" (ID) vinyl tubing 70318 (OD measure 7/16") to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this ...read more -
GECKO MODEL SCREW This stainless steel screw is used to attach the volute cover to the volute on most Wavemaster jet pumps -
Sku: 31228Spring Clamp, 1/2in
1/2" spring clamp for securing 1/2" ID vinyl tubing (70316) to components Item 70316 has an inner diameter of 1/2" and an outer diameter of 3/4" This clamp fits the 3/4" OD Note: Wear eye protection when squeezing these little rascals Service techs ...read more -
Sku: 33850Screw, 8-16 X 1/2in
This screw is used on various air controls and water diverter valve levers & bezels -
Sku: 34465Spring Clamp, 3/8in
3/8" spring clamp (aka wire clamp) is used to secure the 3/8 inch vinyl tubing 70317 (9/16" OD) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers are hose clamp ...read more -
Stainless steel screw used to secure the heater to the equipment compartment floor on Hot Spring & Tiger River spa models Also used on the SilentFlo 5000 Circulation pump and to hold the Ozonator to the wall of the equipment compartment -
This screw is used to hold the front cover of the IQ 2000 and IQ 2020 box in place This screw is not compatible on models made between 2007 and 2009 5 or older models with the upgraded heater relay board (Item #77119) The screw is too long and will hit ...read more -
Sku: 30334Screw, #4 X 1/2in Stainless Steel
Stainless steel screw used in various locations on Hot Spring, Tiger River, Solana, Hot Spot and Limelight spas -
Sku: 30343Screw, #8 X 7/8in
Stainless steel screw for the jet selector water diverter valve lever on all Hot Spring spa models manufactured prior to 1994 that have a jet selector -
This screw was used to hold the thermostat knob in place on the topside control panel used on Tiger River spas from 1992 to 1994 and the round-shaped air control knob on air valves used on Hotspring spas from 1989 to 1993 5 -
Sku: 30105Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 31560Screw, #6-32 X 5/8in
This screw is used to hold the standoff in place in the control box for the main circuit board as well for holding the circuit board to the standoff on 1992-1994 Tiger River spas -
Sku: 30360Screw, 10 X 1/2in Stainless Steel
This screw used to mount bracket for Navigator Remote Control -
6 of these screws are used in the jet selector valve/diverter valve for pre-1994 Hotsprings and Tiger River spas to hold the valve kit ( 20339 ) into the valve body (30502 ) These screws are included in the valve kit -
This screw is used to hold in place the standoffs (35087) that secure the thermostat board (71340)to the topside control panel in Tiger River spas made from 1995 to 1997 -
Sku: 33366Screw, #8-32 X 3/8in Hex Washer-Hd
The screw used on the Freshwater II Ozonator -
Two of these screws are used to hold the thermostat in place to the circuit board on the topside control panel for Tiger River spas from 1992 to 1994 -
Sku: 34009Screw, Control Panel, Tiger River
This screw is used to mount Tiger River control panels to the shell of the spa on the bar top It secures a flip-out tab that clamps the control panel to the shell from the backside of the shell It was used on all models from 1992-1997 -
Sku: 34173Screw 4 X 3/8in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This screw was used to hold the air valve handle in place on Tiger River and Hotspring spas from 1998 to ...read more -
Sku: 33974Screw, 8-32 X 3/8in SS
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Used on the Freshwater II Ozonator -
Sku: 35837Retainer Button, Headrest
OBSOLETE-use 73019 Retainer button (resembles a nylon washer) used in Pillow Retainer Screw Kit This white button is what holds the spa pillows in place -
Sku: 33976
Screw 10-24 X 5/8in Stainless Steel
Obsolete: Available at the local hardware store Used to secure the cartridge style heater elements to their heater housing -
Sku: 70283
Screw, Nut, Arectifier
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Screw, Nut, Arectifier
Showing all 24 results