The team at Backyardplus.com are the best for anything Hot Springs. Super friendly and knowledgeable.On 06/05/2024 by S. O. (verified customer)
Hardware: Ball Stud, Bushing Strain Relief, Clip, Wire Joint
Showing all 19 results
-
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
Sku: 77290Panel Clip, Door/side, NXT
Door and side panel clip NXT model Highlife Collection Grandee NXT (GGN), Envoy NXT (KKN), JetsetterNXT (JJN) To remove Door/Side Panel, loosen the 2 screws on each clip below the panel Slide Door/Side Panel to the "LEFT" Door/Panel will drop ...read more -
Sku: 30099Bushing, Strain Relief
This 3/8" strain relief is used to secure the jet pump(s), circulation pump, light and Ozonator power cords to the bottom of the IQ 2020 Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should ...read more -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP -
Sku: 36586Clip, Extruded Air Valve
Used to hold the air intake for the Freshwater II Ozonator in place on the wall in the equipment compartment near the Ozonator Found in Hotspring and Tiger River Spas with Freshwater II Ozonators -
Sku: 36022Strain Relief 10/3
Heater strain relief used to secure the heaters power cord to the bottom of the IQ Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 30100Strain Relief Bushing, 1/2in
This bushing is used for strain relief of cords that are 1/2" in diameter, such as the cord for the heater in a Hotsprings, Tiger River, or LimeLight spa -
Sku: 73249Panel Clips, Male and Female, QTY 4
Panel clips, male/female, for the removable panels on Hot Spring models, quantity of 4 -
Sku: 30105Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 71614Strain Relief
This strain relief is found on most LX jet pump models -
Sku: 71613Strain Relief #3461
Strain relief #3460 -
Universal Bushing, 0 875 inch, found in Hot Spot Control Box Assembly (37335) This Bushing protects the Electronic T-Stat (75089) from the metal control box housing This part can be found on the 1998 Hot Spot models -
Sku: 30102Bushing, Snap 3/8in Outside Diameter
This bushing is used around openings through the control box used on pre-1997 Hot Springs spas where the copper tubes for the temperature probes and the cable for the spa power on light pass through -
Sku: 31158Clip, Lid Filter Grandee pre 1989
There are four filter clips (31158) and four screws (30341) to hold the filter lid in place Grandee Pre-1989 -
Sku: 78176Panel Clip, 4 pack, Limelight
This panel clip is the bracket that is also considered the male piece for new Limelight all models 2018 and newer -
Sku: 78817Plastic Panel Clip
Plastic Panel Clip for Limelight beginning in 2019 -
Sku: 34717Extrusion, Mount Clip, Model Z
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Extrusion, Mount Clip, Model Z -
Sku: 71166Wire Joint 12-18, 10 pack
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com -
Panel clip Replaced by 78817
Showing all 19 results