The team at Backyardplus.com are the best for anything Hot Springs. Super friendly and knowledgeable.On 06/05/2024 by S. O. (verified customer)
Hardware: Bolt, Bushing Strain Relief, Clamp, Tool
Showing 1–30 of 36 results
-
Sku: 300055Spring Clamp, 3/4 inch
3/4" spring clamp (aka wire clamp) is used to secure the 3/4 inch vinyl tubing (70315) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to ...read more -
Sku: 31134Spring Clamp, 1/4in
Used to secure 1/4" (ID) vinyl tubing 70318 (OD measure 7/16") to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this ...read more -
Sku: 30018Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 31228Spring Clamp, 1/2in
1/2" spring clamp for securing 1/2" ID vinyl tubing (70316) to components Item 70316 has an inner diameter of 1/2" and an outer diameter of 3/4" This clamp fits the 3/4" OD Note: Wear eye protection when squeezing these little rascals Service techs ...read more -
Sku: 70035Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate -
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
Sku: 34465Spring Clamp, 3/8in
3/8" spring clamp (aka wire clamp) is used to secure the 3/8 inch vinyl tubing 70317 (9/16" OD) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers are hose clamp ...read more -
Sku: 30099Bushing, Strain Relief
This 3/8" strain relief is used to secure the jet pump(s), circulation pump, light and Ozonator power cords to the bottom of the IQ 2020 Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should ...read more -
Sku: 36022Strain Relief 10/3
Heater strain relief used to secure the heaters power cord to the bottom of the IQ Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 30100Strain Relief Bushing, 1/2in
This bushing is used for strain relief of cords that are 1/2" in diameter, such as the cord for the heater in a Hotsprings, Tiger River, or LimeLight spa -
Sku: 300602Spring Clamp, 1in
1" spring clamp (wire clamp) used to secure 1" vinyl tubing -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment -
Sku: 30105Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Sku: 71742Bolt, #10 X 2-1/2in
OBSOLETE These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite Illustration (# 5) on the Gliderite parts diagram -
Sku: 71217Hex Head Bolt, 1/4in-#20 X 1in
This bolt is used to fasten the Slide Lock Bar to the Side Arm -
Sku: 71614Strain Relief
This strain relief is found on most LX jet pump models -
Sku: 71613Strain Relief #3461
Strain relief #3460 -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1) -
Universal Bushing, 0 875 inch, found in Hot Spot Control Box Assembly (37335) This Bushing protects the Electronic T-Stat (75089) from the metal control box housing This part can be found on the 1998 Hot Spot models -
Hex bolt, 1/4in-20 x 1-1/2in stainless steel -
Sku: 32748Lag Bolt 3in
3in lag bolt -
Sku: 30102Bushing, Snap 3/8in Outside Diameter
This bushing is used around openings through the control box used on pre-1997 Hot Springs spas where the copper tubes for the temperature probes and the cable for the spa power on light pass through -
Sku: 71218Bolt, #20 X 1/4in. X 2in. Hex Head
Attaches the sidearm to the pivot wheel on all spa models (except the Hot Spring Classic) -
Sku: 34174Bolt, 1/4in-20 X 5/8in 100 Degree
Bolt, 1/4in-20 x 5/8in 100 degree -
Sku: 71188
Bolt, 3/8in-24 x 2, pack of 5
Bolt, 3/8in-24 x 2, pack of 5 -
Sku: 71931
Phone Jack Crimp Tool
Phone jack crimp tool -
Sku: 32746
Bolt, Lag 4in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Bolt, Lag 4in -
Sku: 34487
Snap Clamp Snp #6
OBSOLETE: Use 31134 This is a #6 size snap clamp used on 1/4" vinyl tubing Snap Clamp (Min Dia In ) 0 449 / (Max Dia In ) 0 511
Showing 1–30 of 36 results