Great serviceOn 04/19/2024 by H. P. (verified customer)
Brand: Cover Cradle Ii, Starite
Showing all 22 results
-
Sku: 31134Spring Clamp, 1/4in
Used to secure 1/4" (ID) vinyl tubing 70318 (OD measure 7/16") to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this ...read more -
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 30413Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 70035Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70036Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 30297Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Sku: 30220Volute O-Ring, Starite
Volute O-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993 -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
Sku: 72574Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP -
Sku: 72714Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment -
Sku: 72715Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
This diffuser lock washer is used with the screws and nuts that belong to heater 20286 50-BYP and 20286 75-BYP -
Sku: 71105Bracket, Corner (G/K)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Bracket, Corner (G/K) -
OBSOLETE-Use the 71107-BYP -
Sku: 71110Screw, #10 X 1-1/2in
Obsolete from the factory -Available at most hardware stores 1-1/2in Phillips flat head screw that attaches the side hinge base to the spa cover -
Sku: 71109Screw, #10 X 1/2in, Pan Head
Obsolete from the factory - Available at most hardware stores Screw, #10 X 1/2in, Pan Head This Phillips Head screw is used on various cover lifter models -
Sku: 72716
Hardware Bag #4, Cover Cradle II
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com
Showing all 22 results