Purchased the mother board for our 2006 hot springs Vanguard. Watched the video that Paul made in the installation. He goes over everything you need and the process along the way. Makes the task so effortless. I did the change out over a weekend and had a question. Email BackYardPlus and got a very fast response from Craig. I can’t say enough about the friendlyness, knowledge this company has. Will always be getting my parts from BackYardPlus. Saved me $$$ for sure. Again thank you Paul & Craig.On 03/21/2024 by C. S. (verified customer)
Brand: Hot Spring, Iq 2000, Spaudio System, Wavemaster 9200
Showing 91–120 of 165 results
-
Sku: 72017Fastener, LED Light (Qty 4)
Fasteners used to hold the housing for the LED light assembly in place on Hotsprings, Tiger River, and Limelight spas These are included if you purchase a replacement light assembly -
This screw is used for holding the IQ 2000 and IQ 2020 control boxes in place on the mounting bracket in Hotsprings, Tiger River, and Limelight spas -
Sku: 36018IQ Control Box Bracket
This aluminum bracket attaches to the spa door frame to enable the IQ Control Box to mount securely to this bracket The bracket does not come with the two 36898 screws that attach it to the control box Simple wood screws are used to attach it to the wood ...read more -
This screw was used to hold the thermostat knob in place on the topside control panel used on Tiger River spas from 1992 to 1994 and the round-shaped air control knob on air valves used on Hotspring spas from 1989 to 1993 5 -
Sku: 30120Lug, Grounding
Used on various components in the equipment compartment to provide a place for the grounding wire to attach to -
Sku: 30105Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Non-metallic hinge for all pre-1995 wooden Hot Spring equipment compartment doors (access doors) -
Sku: 34304Standoff, #10 – 32 X 1/2in
This standoff is found on the backside of the 1994-1997 Hot Spring control panels -
Sku: 73451Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Lock washer for the diffuser screw on a Wavemaster 7000 (ver 2) and Wavemaster 9000 jet pump -
Sku: 20018Hinge, 7in
This door hinge was used on the Hot Spring spas -
Sku: 70946Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Flat Volute washer for the Wavemaster 7000 version 2 and he Wavemaster 9000 -
Door screws in Mocha color for Highlife spas beginning in 2014 Set of six -
Sku: 70268Insulation, Fiberglass 36 X 65in
The insulation used to insulate the top of the equipment compartment in spas made prior to 2000 It is usually wrapped around the bottom of the spa step -
Sku: 72855Female Quick Disconnects (10)
These quick disconnects are used to adapt one male spade connector to be able to accept two female spade connectors Used a lot with the sound system installations It should not be used on higher amperage applications -
Sku: 30399Insert, Door, Classic F
-
Sku: 76034-2Flange Connectors, Hot Spring Lighted Logo
Set of two connectors (fasteners) that attach the backside of the lighted Hot Spring logo onto the side cabinet on all second quarter 2009 forward Hot Spring spa models -
Sku: 74130Dream Jet O-Ring, Cylinder Base
O-Ring, Cylinder Base 2001 Hot Spring Landmark Dream Jet Massage System -
Sku: 73256Clarion Brackets
These brackets are used to mount the Clarion Light Bars to the spa or step or where ever desired Five sets of left and right pairs are included in each pack -
Sku: 72715Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
Sku: 71072Retainer Clip
Used on the 1995-1999 Hot Spring Dream Pillow Neckjet -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor -
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1) -
Phillip head stainless steel screw, 8-18 x 3/8in for control panels on Hot Spring models 1994-1997 -
Sku: 34182Gasket, Silicone Jet 2-1/2in
Red silicone gasket (rubber gaskets dissolve in chlorinated water) fits behind the wall fitting nut and the spa shell on the 1993-1994 Hot Spot Z model spa and is used on the jet assembly on the 1995-1999 Hot Spring Dream Pillow Jet -
Sku: 33368Screw, 10-32 x 3/8in
This screw is used on Hotsprings Spas made from 1994 to 1996 to hold the plastic stand-off in place on the mounting plate from behind This stand-off accepts the screws from the front of the control panel that are used to hold the control panel in place -
Knob spring, for the rear side of the control panel, found on Hot Spring models from 1994-1997 -
Sku: 30369Screw, #6 X 5/8in Stainless Steel
Stainless steel screw, #6 x 5/8in, for the control panel on Hot Spring Models from 1989-1993
Showing 91–120 of 165 results