Purchased the mother board for our 2006 hot springs Vanguard. Watched the video that Paul made in the installation. He goes over everything you need and the process along the way. Makes the task so effortless. I did the change out over a weekend and had a question. Email BackYardPlus and got a very fast response from Craig. I can’t say enough about the friendlyness, knowledge this company has. Will always be getting my parts from BackYardPlus. Saved me $$$ for sure. Again thank you Paul & Craig.On 03/21/2024 by C. S. (verified customer)
Brand: Hot Spring Pre 89, Wavemaster 4000
Showing 91–120 of 145 results
-
This screw was used to hold the thermostat knob in place on the topside control panel used on Tiger River spas from 1992 to 1994 and the round-shaped air control knob on air valves used on Hotspring spas from 1989 to 1993 5 -
Sku: 30120Lug, Grounding
Used on various components in the equipment compartment to provide a place for the grounding wire to attach to -
Sku: 30105Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Non-metallic hinge for all pre-1995 wooden Hot Spring equipment compartment doors (access doors) -
Sku: 34304Standoff, #10 – 32 X 1/2in
This standoff is found on the backside of the 1994-1997 Hot Spring control panels -
Sku: 73451Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Lock washer for the diffuser screw on a Wavemaster 7000 (ver 2) and Wavemaster 9000 jet pump -
Sku: 20018Hinge, 7in
This door hinge was used on the Hot Spring spas -
Sku: 70946Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Flat Volute washer for the Wavemaster 7000 version 2 and he Wavemaster 9000 -
Sku: 30399Insert, Door, Classic F
-
Sku: 73256Clarion Brackets
These brackets are used to mount the Clarion Light Bars to the spa or step or where ever desired Five sets of left and right pairs are included in each pack -
Sku: 72715Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor -
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1) -
Phillip head stainless steel screw, 8-18 x 3/8in for control panels on Hot Spring models 1994-1997 -
Sku: 33368Screw, 10-32 x 3/8in
This screw is used on Hotsprings Spas made from 1994 to 1996 to hold the plastic stand-off in place on the mounting plate from behind This stand-off accepts the screws from the front of the control panel that are used to hold the control panel in place -
Knob spring, for the rear side of the control panel, found on Hot Spring models from 1994-1997 -
Sku: 30369Screw, #6 X 5/8in Stainless Steel
Stainless steel screw, #6 x 5/8in, for the control panel on Hot Spring Models from 1989-1993 -
Sku: 30361Screw, Metal #10 X 3/4in
Metal screw, #10 x 3/4in, found on the control panel of Hot Spring models from 1989-1993 -
Sku: 30360Screw, 10 X 1/2in Stainless Steel
This screw used to mount bracket for Navigator Remote Control -
This screw is used to secure the volute to the pump base 70959 -
Stainless steel Phillips head sheet metal screw, 8x3/4in -
Sku: 33570Washer, #10 .200 X .359 X .063
Washer, #10 200 X 359 X 063 -
Mounting plate found on the backside of all 1994-1997 Hot Spring Classic spas control panels -
Sku: 34359Screw, #8-16 X 1/2in
Screw, #8-16 X 1/2in, found on control panels on Hot SPring models from 1994-1997 -
Sku: 34362Screw, #10-32 X 1-1/2in, White Head
This white colored tipped 1-1/2" long screw secures the control panel in place on the 1994-1997 Hot Spring Classic spa model -
Sku: 34481Screw Receptacle
Screw Receptacle -
One of two volute washers on the Wavemaster 7000 (second version) and the Wavemaster 9000 jet pump
Showing 91–120 of 145 results