Super service. Thank you.On 05/21/2024 by N. M. (verified customer)
Showing 31–60 of 166 results
-
Espresso colored screws found on the exterior synthetic wood paneling on all Limelight spa models This item is a quantity of 10 screws These screws are used on each side of the spa to mount the siding to the metal frame of the spa The screws are color ...read more
-
Four of these stainless steel screws are used to mount the control head (the electronic part of the control panel) to the control panel bezel These are accessible from behind the control head
-
Sku: 30407
Washer, Nylon Flt (Thin)
Nylon washer for the jet selector water diver valve on all Hot Spring & Tiger River spa models manufactured prior to 1994 -
This stainless steel impeller screw (left-hand threads) screws onto the end of the motor shaft to secure the impeller from spinning off of the Sta-rite Maxi-Glass 1hp & 2hp pumps that were used in Hot Spring spas prior to 1994
-
Sku: 34363
Screw,#10-32 X 1-1/2in
This gray-colored tipped 1-1/2" long screw secures the control panel in place on all 1994-1997 wood-sided Hot Spring models and is also found in various other locations such as the Dream Pillow etc -
Sku: 70191
Screw, Drain Slide 1-1/4in
Drain slide screw, 1-1/4" -
Stainless steel Phillips head screw, 10-24x1 1/2, use on equipment doors
-
Sku: 30383
Brown Nylon Screw
Brown nylon screw -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment
-
Sku: 2317
Screw, #10 x 1/2″
Stainless steel screw -
Sku: 30347
Screw, #10-24 X 1/2in Stainless Steel
Stainless steel screw -
Driftwood colored screws found on the exterior synthetic wood paneling on all Limelight spa models This item is a quantity of 10 screws One set of these screws is used on each side of the spa They are colored to match the color of the spa cabinet
-
This screw is used for holding the IQ 2000 and IQ 2020 control boxes in place on the mounting bracket in Hotsprings, Tiger River, and Limelight spas
-
This screw was used to hold the thermostat knob in place on the topside control panel used on Tiger River spas from 1992 to 1994 and the round-shaped air control knob on air valves used on Hotspring spas from 1989 to 1993 5
-
Lock washer for the diffuser screw on a Wavemaster 7000 (ver 2) and Wavemaster 9000 jet pump
-
Sku: 70946
Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Flat Volute washer for the Wavemaster 7000 version 2 and he Wavemaster 9000
-
Door screws in Mocha color for Highlife spas beginning in 2014 Set of six
-
Sku: 71742
Bolt, #10 X 2-1/2in
OBSOLETE These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite Illustration (# 5) on the Gliderite parts diagram -
Sku: 39281
Screw, Hot Spot Door, Cream
This screw is used on Hot Spot spas from 1998 to 2010 It is a stainless steel Phillips head screw with a pan head that has been painted to match the color of the skirting and door of the spa -
Sku: 74790
Exterior Screws, Autumn, Limeight
Autumn colored screws found on the exterior synthetic wood paneling on all Limelight spa models from 2008-2011 This item is a quantity of 10 screws These screws are color-matched to the paneling used on the outside of the spa -
Sku: 71744
Washer, Gliderite
These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter -
Sku: 71217
Hex Head Bolt, 1/4in-#20 X 1in
This bolt is used to fasten the Slide Lock Bar to the Side Arm -
Sku: 71556
Screw, 10-32 X 1/2in Shwh Zinc Plate
Screw, 10-32 x 1/2in -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor
-
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump
-
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1)
-
Phillip head stainless steel screw, 8-18 x 3/8in for control panels on Hot Spring models 1994-1997
-
Sku: 33368
Screw, 10-32 x 3/8in
This screw is used on Hotsprings Spas made from 1994 to 1996 to hold the plastic stand-off in place on the mounting plate from behind This stand-off accepts the screws from the front of the control panel that are used to hold the control panel in place -
Hex bolt, 1/4in-20 x 1-1/2in stainless steel
Showing 31–60 of 166 results