quick ship ,as described and was perfect transaction. ThanksOn 06/13/2024 by B. H. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing all 21 results
-
Sku: 1044101-72228-AM-BYP
Tubing Kit, Del-Ozone-1/4in with Check valve
This 1/4" ID (3/8" OD) ozone-resistant tubing works with UO3 ozone generator It includes an attached 1/4" ozone-resistant check valve, clamps, mounting screws, and new flag terminals This assembly is approx five feet in length Note: There is a small ...read more -
Sku: 1044101-72228-BYP
Tubing Kit, Freshwater III Ozonator-1/4in Tygon/Kynar with Check valve
This 1/4" ID (3/8" OD) Kynar/Tygon ozone-resistant tubing kit comes standard with the Freshwater III Ozonators It is the replacement for all Freshwater 3 ozonators It includes an attached 1/4" ozone-resistant check valve This assembly is approx six feet ...read more -
Sku: 35233
Water Check Valve, 3/4 inch
This 3/4" water check valve is installed in the inlet side of the circulation pumps plumbing to prevent the backflow of water through the circulation pump once the jet pump is activated All water check valves have arrows stamped on the outside to indicate ...read more -
Air check valve for Hot Spring, Tiger River, and Hot Spot spa models This check valve is located in the equipment compartment under the bartop Its primary function is to prevent water from back flowing into the equipment compartment should a hydrotherapy ...read more
-
Sku: 38390
Check Valve, Air, with Ball 1/2in
It is used to prevent water from backing into the airlines when the jets are off It is at the back of the Moto-Massage housing and glued into a 90-degree elbow It is also on the jetstream jets -
Sku: 1044101
Check Valve (Ozone) Freshwater Ozone, 1/4in O.D.
Over time an Ozonator check valve will breakdown under the harsh conditions of ozone Our OEM check valves have a special diaphragm (Viton) that enables them to last longer than rubber Rubber diaphragms last about a month before the rubber becomes hard -
This air check valve is located in the equipment compartment, up high, under the bar top If a hydrotherapy jet should become obstructed (like when a guest sticks their finger in the jet), this item becomes critical in preventing water from back flowing into ...read more
-
Sku: 72701
Hartford Loop Assembly
This retrofit kit is used to replace the air check valve that was used in some Hot Spring spa models This kit replaces the obsolete 72342 Check your serial number in the parts finder above to be sure this part is for your spa -
This "Jet System" check valve is used on all Hot Spring models and all Tiger River spas This check valve engages when the diverter valve is changed to different positions For convenience, the inside diameter of this check valve is 1-1/2" and the outside ...read more
-
Sku: 71981
Check Valve, with Spring, 1-1/2in
1-1/2" spring style check valve is commonly found between the jet pump and filter housing on Tiger River spas This check valve automatically closes when the Tiger River spas jet pump is turned off so the circulation pump (Silentflo 5000) can then draw water ...read more -
Sku: 39705
5 Port Air Manifold, 1in x 3/8in
PVC air manifold, 1" X 3/8", 5-Port -
Sku: 39707
Air Manifold, PVC 1inx3/8in, 4 Port
PVC air manifold, 1" X 3/8", 4-Port -
Sku: 36977
Air Manifold, 4 Port, 3/8in Barbs
This four-port manifold is typically used to feed air to the Precision Jets in a Hot Spring and Tiger River spa This 4 port manifold comes with one end capped off and the other end is 1" slip Depending on the current configuration of yours, the 1" may need ...read more -
Sku: 70173
Check Valve (Water) 1/2in
This 1/2" water check valve is used on the discharge side of the old Laing circ pumps in pre-1990 Hot Spring 115volt Sovereign, Classic, Prodigy & Jetsetter models This is for 1/2" plumbing If your plumbing is 3/4" then use part 35233 -
PVC air manifold, 1" Barb Adap, 3/8", 2-Port
-
Sku: 36295
8-Port Air Manifold
8-port PVC air manifold -
Sku: 72032
10 Port Air Manifold
Air manifold: 10" long with 1/2" barbed in and 3/8" barbed out x 10 -
Sku: 39703
7 Port Air Manifold, 1in X 1in X 3/8in
This 6 port air manifold is used in various spa models It's a one-inch slip with six 3/8" barbed nipples to connect the 3/8" tubing For the 1/2" version see part 38397 -
This 6 port air manifold is used in various spa models It's half-inch slip with six 3/8" barbed nipples to connect the 3/8" tubing For the 1" version see part 39703
-
Sku: 1110501
10 Port Air Manifold
This manifold allows 10 air lines to be connected to one air valve It is used mostly on Hot Spot brand spas but is used on other brands as well The PVC fittings are 3/4" slip and PVC primer and cement should be used to bond them And the 10 fittings ...read more -
Sku: 302364
3/4 IN Check Valve
3/4" check valve found on many Hot Spring models beginning in 2007, Hot Spot beginning in 2019, and Limelight models beginning in 2019
Showing all 21 results