quick ship ,as described and was perfect transaction. ThanksOn 06/13/2024 by B. H. (verified customer)
Brand: Hot Spring | Plumbing: Barbed Adapter, Plug, Union
Showing all 20 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system or jets in a Hot Spring & Tiger River spa It simply glues into a 1/2" PVC coupling or elbow with regular PVC cement -
Sku: 010009Barbed adapter 1 in x 3/8 Spigot
Barbed adapter 1 inch by 3/8 inch 425-5010 BARB ADAP 1IN(1)3/8IN -
Barbed adapter which is 1/2" male threads on one end and 1/2" barbed on the other -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system of Hot Spring spa models -
Sku: 30586Barbed Adapter, 1/4in X 5/16in
This barbed adapter is used in various places but primarily in the Moto-Massage niche for the small silicone Moto-Massage Jet air tube to slip onto on pre-1997 Hot Spring spa models -
Barbed adapter which is 3/4" male threads on one end and 1/2" barbed on the other -
Sku: 30699Plug, 1-1/2in Spig
This PVC fitting is used to plug 1 1/2" female PVC slip fittings It should be attached using PVC primer and cement, which is available at your local hardware store It is made out of white PVC plastic -
Sku: 30698Plug, 1in Spig
This is a 1" PVC plug It is used to plug a 1" female PVC fitting and should be attached using PVC cement and PVC primer This will usually be used when a fitting has multiple openings, and not all of the openings are being used -
Sku: 30696Plug 1/2in Spig
Plug, PVC, 1/2" Spig -
Sku: 30549Union, 1-1/2in Slip x Threaded
Union, 1-1/2in slip x threaded -
Sku: 36581Barbed adapter 3/4 in x 1/2 Spigot
Barbed adapter 3/4 in x 1/2 spigot -
Sku: 1291501Barbed adapter 3/8 in x 3/4 Spigot
Barbed adapter 3/8 in x 3/4 spigot -
Sku: 30552Adapter, Union 1-1/2in
Used on the 30215 Starite Jet pump This adapter screws into the 1 1/2" FPT fitting on the jet pump and accepts the union used on spas that use the 30215 jet pump in the early 90s This piece will only work with the original union If the union has been ...read more -
Sku: 31503Plug, Drain Slide 1-1/2in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com 1-1/2' male threaded PVC plug Available at most hardware stores in various forms -
Sku: 30242Plug, Freeze Pump
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com This plug is used to close off the threaded fittings that are built into most jet pump volutes These ...read more
Showing all 20 results