Best place ever, always goodOn 05/31/2024 by M. D. (verified customer)
Brand: Hot Spring Pre 89 | Plumbing: Barbed Adapter, Union, Wallfitting
Showing all 21 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: 30490Wallfitting, Rear
This fitting is used on many different Hot Spring spa models in various places including the grill style filter compartment as part of the filter assembly Also used in the filter compartment of all 1992-1996 Tiger River spa models -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system or jets in a Hot Spring & Tiger River spa It simply glues into a 1/2" PVC coupling or elbow with regular PVC cement -
Sku: 010009Barbed adapter 1 in x 3/8 Spigot
Barbed adapter 1 inch by 3/8 inch 425-5010 BARB ADAP 1IN(1)3/8IN -
Barbed adapter which is 1/2" male threads on one end and 1/2" barbed on the other -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system of Hot Spring spa models -
Sku: 30586Barbed Adapter, 1/4in X 5/16in
This barbed adapter is used in various places but primarily in the Moto-Massage niche for the small silicone Moto-Massage Jet air tube to slip onto on pre-1997 Hot Spring spa models -
Sku: 71128Wallfitting, Drain Drilled
Wall fitting, rear drain, 1/2" drilled, Hot Spring Rear wall fitting located in the footwell of the spa Front wall fitting part 30488 -
Barbed adapter which is 3/4" male threads on one end and 1/2" barbed on the other -
Sku: 71263Wallfitting, Gray, without Knockout
Gray wallfitting, for Hot Spring -
Sku: 30549Union, 1-1/2in Slip x Threaded
Union, 1-1/2in slip x threaded -
Sku: 36581Barbed adapter 3/4 in x 1/2 Spigot
Barbed adapter 3/4 in x 1/2 spigot -
Sku: 1291501Barbed adapter 3/8 in x 3/4 Spigot
Barbed adapter 3/8 in x 3/4 spigot -
This rear wall fitting is found on the backside of the spa shell and attached to the drain plumbing It has a front wall fitting (30488) and o-ring (30482) that screws into it from the front side of the spa shell The front wall fitting has a female 1-1/2" ...read more -
Sku: 30552Adapter, Union 1-1/2in
Used on the 30215 Starite Jet pump This adapter screws into the 1 1/2" FPT fitting on the jet pump and accepts the union used on spas that use the 30215 jet pump in the early 90s This piece will only work with the original union If the union has been ...read more -
Sku: 10430Rear Venturi Wallfitting
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Rear wallfitting for the Hydro-Air jet used in all Hot Springs models in 1990 and 1991 -
Sku: 33729Wallfitting, Pvc Rear
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com -
Sku: 36208
Wallfittiing #1 Front, Gray Plg
OBSOLETE-Use 30488
Showing all 21 results