The team at Backyardplus.com are the best for anything Hot Springs. Super friendly and knowledgeable.On 06/05/2024 by S. O. (verified customer)
Plumbing: Adapter, Plug, Union, Wallfitting
Showing 1–30 of 57 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 32267-1Drain Plug, Wavemaster
This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline For spas with a bleedline, the 32267 is used in place of this fitting This drain plug can be ...read more -
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit -
Sku: 31417Adapter, 3/4in Barbed X 3/4in Slip
This barbed fitting is primarily used to connect 3/4" vinyl tubing to various places within the circulating/heating system of Hot Spring & Tiger River from 1990 forward This PVC fitting is often found glued into a 90-degree elbow rising from the floor of ...read more -
Sku: 34504Adapter, 3/4in Sp X 1/4in Sp
This adapter glues into a 3/4" female PVC slip fitting using PVC primer and cement and accepts a 1/4" vinyl hose that can be secured using PVC cement as well or a hose clamp -
Sku: 11080449-020 2in Plug
This is a 2" PVC plug It can be used to plug any 2" female PVC fitting and should be installed using PVC primer and cement You can get PVC cement at your local hardware store -
Sku: 30703Adapter, 3/4in X 3/4in Mht X Slip
This PVC fitting glues on to a 3/4" male PVC rigid or flexible pipe and allows a 3/4" female pipe thread to connect to it On Hotsprings and Tiger River spas, it's used as part of the drain system, to allow a garden hose to be connected and water to be ...read more -
Sku: 30490Wallfitting, Rear
This fitting is used on many different Hot Spring spa models in various places including the grill style filter compartment as part of the filter assembly Also used in the filter compartment of all 1992-1996 Tiger River spa models -
This coupling is made from an ozone resistant plastic called Kynar It is connected to the side of the newest style of Freshwater III Ozonator, 72602 The ozone tubing connects onto this barbed fitting If your barbed fitting breaks off, this factory ...read more -
This threaded wall fitting is located in the bottom of the filter compartment on all 1997-2010 Tiger River Bengal, Caspian, Sumatran & Siberian spa models This is where the filter standpipe screws into -
Sku: 71128Wallfitting, Drain Drilled
Wall fitting, rear drain, 1/2" drilled, Hot Spring Rear wall fitting located in the footwell of the spa Front wall fitting part 30488 -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
Sku: 31556Adapter, 1/4in X 1/4in Spig X Slip
Adapter, Barb x Socket, 1/4" x 1/4" -
Sku: 31348Adapter, 1-1/2in Mipt
This male adapter screws into a 1-1/2" jet pump volute in order for a 1-1/2" compression coupling (pump union) to screw onto the adapter -
Sku: 30697Plug, 3/4in Spig
Plug, PVC, 3/4" Spig This plug is made out of PVC and fits in a female PVC slip fitting It can be used to plug an extra port on a manifold or tee that is not needed Or cap off a piece of plumbing that is no longer used -
PVC elbow that allows a 3/4" barbed fitting and a 3/4" threaded fitting to be connected together Both fittings are male, and the barbed fitting should be secured using hose clamps, and the threaded fitting should be wrapped in Teflon tape before installing ...read more -
Sku: 39438Adapter, Ell 1/2in Hose X 1/4in Mpt
Adapter, barbed ell, PVC, 1/2" hose x 1/4", male pipe thread -
Sku: 70906Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Sku: 30690Adapter, 3/8 X 1/2 Mipt X Fipt
This adapter Used with the 30118 thermostat cord grip -
Sku: 30702Adapter, 3/4in X 1/2in Mht X Slip
This PVC fitting accepts a 1/2" male slip fitting or 1/2" PVC pipe and should be attached using PVC primer and cement The other end is a 3/4" male pipe thread and can be used to connect fittings such as a garden hose This part is used commonly in the ...read more -
Sku: 71263Wallfitting, Gray, without Knockout
Gray wallfitting, for Hot Spring -
Sku: 31486Adapter, 3/4in Slip
Adapter, Barb x Socket, 3/4" x 3/4" -
Sku: 30699Plug, 1-1/2in Spig
This PVC fitting is used to plug 1 1/2" female PVC slip fittings It should be attached using PVC primer and cement, which is available at your local hardware store It is made out of white PVC plastic -
Sku: 30698Plug, 1in Spig
This is a 1" PVC plug It is used to plug a 1" female PVC fitting and should be attached using PVC cement and PVC primer This will usually be used when a fitting has multiple openings, and not all of the openings are being used -
Sku: 30696Plug 1/2in Spig
Plug, PVC, 1/2" Spig -
2" X 1-1/2" male adapter commonly used on the suction side of pumps -
This PVC fitting has a female PVC slip fitting and a male pipe thread fitting So it can accept a 1" PVC pipe or male PVC slip fitting and can screw into a 3/4" female pipe threaded fitting
Showing 1–30 of 57 results