Best place ever, always goodOn 05/31/2024 by M. D. (verified customer)
Plumbing: Barbed Adapter, Cap, Injector, Union
Showing 1–30 of 38 results
-
Sku: 74078Injector, Freshwater Ozone, Black
The injector fits in-line after the Silentflo 5000 (discharge side and after the heater) This Kynar plastic "venturi" injector is ozone resistant and is used with the Freshwater III High Output Ozonator by Watkins manufacturing, item 72602 -
Sku: 74077Injector, Freshwater Ozone, Red
This red ozone injector was used with the Freshwater I & Freshwater III (for Hot Spot & Solana spas) It is designed to allow a pre-determined amount of ozone bubbles per minute to enter the spa's circulating system The injector is matched to the ...read more -
Sku: 30700Cap, Drain Valve – 3/4in with Washer
Black 3/4" hose bib thread cap used on the drains of 1993 forward Hot Spring, Tiger River, Hot Spot, and Solana, and Limelight spa models It also includes the washer This cap is used both on the "Primary" Drain Valve, and the "Secondary" Drain Valve -
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system or jets in a Hot Spring & Tiger River spa It simply glues into a 1/2" PVC coupling or elbow with regular PVC cement -
Sku: 010009Barbed adapter 1 in x 3/8 Spigot
Barbed adapter 1 inch by 3/8 inch 425-5010 BARB ADAP 1IN(1)3/8IN -
Sku: 73297Cap, Drain Valve Assembly
Drain valve black cap, washer and ring assembly used on 2004 forward Hot Spring and Tiger River spa models -
Barbed adapter which is 1/2" male threads on one end and 1/2" barbed on the other -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system of Hot Spring spa models -
Sku: 30586Barbed Adapter, 1/4in X 5/16in
This barbed adapter is used in various places but primarily in the Moto-Massage niche for the small silicone Moto-Massage Jet air tube to slip onto on pre-1997 Hot Spring spa models -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
Sku: 70906Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Barbed adapter which is 3/4" male threads on one end and 1/2" barbed on the other -
Sku: 301035Barbed Adapter, 432-007525
Barbed adapter -
Sku: 74350Red Ozone Injector FreshWater III
Ozone Injector assembly including tubing and check valve for Hot Spot and Solana model spas without dedicated circulation pumps This injector is designed for when a 2-speed jet pump is used to circulate the water through the heater -
This is a PVC adapter that has 1/2" male threads on one end and 3/8" barbed on the other Allows a 1/2" female fitting to be adapted to 3/8" tubing that has no fitting on the end -
Sku: 39314Ozone Injector, Freshwater 1
This red ozone injector is used in conjunction with the Freshwater I Ozonator It designed to allow a pre-determined amount of ozone bubbles per minute to enter the spa's circulating system -
Sku: 72231Air Injector Assembly
Air injector -
Sku: 30694Cap, 2in Slip
This is a cap that can be used to cap off a 2" male slip fitting or a 2" PVC pipe, either rigid or flexible PVC primer and PVC cement should be used to attach this fitting -
Sku: 30693PVC Cap 1 1/2in Slip
This is a cap which can be used to cap off a 1 1/2" male slip fitting or a 1 1/2" PVC pipe, either rigid or flexible PVC primer and PVC cement should be used to attach this fitting -
This is a PVC adapter that has 1/4" male threads on one end and 3/8" barbed on the other Allows a 1/4" female fitting to be adapted to 3/8" tubing that has no fitting on the end -
This barbed adapter has a 1/2" barbed fitting on one end, and a 1/2" male pipe thread fitting on the other end Then on the side of it, it has a 1/4" barbed fitting -
Sku: 30549Union, 1-1/2in Slip x Threaded
Union, 1-1/2in slip x threaded -
Sku: 11200013 PORT END CAP
3-port end cap for a 3-port manifold -
Sku: 36581Barbed adapter 3/4 in x 1/2 Spigot
Barbed adapter 3/4 in x 1/2 spigot -
Sku: 1291501Barbed adapter 3/8 in x 3/4 Spigot
Barbed adapter 3/8 in x 3/4 spigot -
Sku: 30552Adapter, Union 1-1/2in
Used on the 30215 Starite Jet pump This adapter screws into the 1 1/2" FPT fitting on the jet pump and accepts the union used on spas that use the 30215 jet pump in the early 90s This piece will only work with the original union If the union has been ...read more
Showing 1–30 of 38 results