The team at Backyardplus.com are the best for anything Hot Springs. Super friendly and knowledgeable.On 06/05/2024 by S. O. (verified customer)
Showing all 19 results
-
GECKO MODEL SCREW This stainless steel screw is used to attach the volute cover to the volute on most Wavemaster jet pumps
-
Sku: ML-1OZ-BYP
Silicone Grease, 1 oz. Tube
Silicone grease ideal for lubricating o-rings -
Sku: 70036
Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 30297
Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Impeller screw for the Wavemaster 7000 (v 1) This screw is reversed thread (left hand thread) This screw is not needed if you are purchasing a new impeller 2014 forward
-
Sku: 70945
Gasket, Impeller Screw Wavemaster 9000
This little gasket fits over the impeller screw and is snugged into place against the impeller when the screw is tightened -
This stainless steel impeller screw (left-hand threads) screws onto the end of the motor shaft to secure the impeller from spinning off of the Sta-rite Maxi-Glass 1hp & 2hp pumps that were used in Hot Spring spas prior to 1994
-
Sku: 70126
Pump Mounting Bracket, Starite 2HP
Pump mounting bracket used to secure the 2HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment -
Sku: 70031
Pump Mounting Bracket, Starite 1HP
Pump mounting bracket used to secure the 1HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment -
Sku: 70946
Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Sku: 71556
Screw, 10-32 X 1/2in Shwh Zinc Plate
Screw, 10-32 x 1/2in -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor
-
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump
-
This screw is used to secure the volute to the pump base 70959
-
This nut goes onto the volute bolt that secures the seal place to the volute
-
Sku: 70404
Diffuser Screw, 8-32 X 1in Phillips, Wavemaster 7000 V1
This item is obsolete and replaced by:
70951Obsolete: Factory replacement suggestion item 70951 This is the screw that secures the diffuser to the seal plate on a Wavemaster 7000 (v 1) pump -
Sku: 33143
Nut,#14-20 Hex Serrated Flange
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com -
Sku: 71563
Screw, 1/4in-20 5/16in 9973000
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Screw, 1/4in-20 5/16in 9973000 -
Sku: 71728
Screw Pk8 #8-32 X 5/8in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Screw Pk8 #8-32 X 5/8in
Showing all 19 results