On 03/05/2024 by C. W. (verified customer)
Showing 61–90 of 148 results
-
Sku: 71030
Shaft Seal, Wavemaster 7000 (version 2) and 9000
This item is obsolete and replaced by:
71030-BYPReplacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 See item 71030-BYP for after-market shaft seal -
O-ring that mounts onto the front of the pump diffuser
-
Sku: 70401
Impeller, 1Hp Wavemaster 7000 (v.1)
Replacement impeller for the first Wavemaster 7000 used on the 1993-1996 Hot Spring Classic, 1993-1995 Grandee, Highlife and Sovereign spa models The impeller screws onto the motor shaft (right-hand threads) This impeller does not require an impeller screw -
Sku: 72349
Rubber Feet, Wavemaster (Set of 4)
Rubber Mounts (feet) for the Wavemaster jet pump These are used to buffer the vibrations from the jet motor within the equipment compartment Comes in a set of four -
Sku: 70039
Slinger, Starite
Water slinger used on the 1HP and 2HP Sta-rite Max-E-Glas jet pump on Hot Spring spas The slinger prevents water, that may be leaking from the shaft seal, from dripping back into the windings of the electric motor and corroding that motor -
This slinger is for the Wavemaster 7000 version 2 and the Wavemaster 9000 If the pump's shaft seal was to begin leaking, the slinger would "sling" water off the shaft to prevent that water from migrating into the electric motor
-
Sku: 30261
O-Ring, Union, Starite
O-ring for the compression fitting union used on the 30215 Starite Jet Pump -
Sku: 72344
Exhaust Hose, Wavemaster
This exhaust hose connects onto the rear of the jet pumps shroud (if equipped) to discharge hot air from the jet pump motor This method of cooling the jet pump ensures a longer lifespan of the pump's motor -
Sku: 72072-1.5
Split Nut for 1.5in Compression Fittings
This 1-1/2" split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age, and over-tightening The two halves of this fitting are held together by two screws -
The diffuser mounts onto the seal plate of the Wavemaster 7000 second version and the Wavemaster 9000 jet pump using seven stainless steel screws
-
Volute for the Wavemaster 7000 version 2 and the Wavemaster 9000 v 1
-
Sku: 30221
Diffuser, Starite
Sta-rite Diffuser used on the 1HP and 2HP Max-E-Glas jet pumps on Hot Spring spa models -
Sku: 30221-BYP
Diffuser, Starite- After Market
After-market Sta-rite Diffuser used on the 1HP and 2HP Max-E-Glas jet pumps on Hot Spring spa models -
This pad goes between the motor base and the plastic base buffer against noisy motor vibrations
-
Impeller screw for the Wavemaster 7000 (v 1) This screw is reversed thread (left hand thread) This screw is not needed if you are purchasing a new impeller 2014 forward
-
Sku: 70408
Diffuser, Wavemaster 7000 (v.1)
The diffuser screws onto the seal plate of the Wavemaster 7000 (v 1) with 3 screws which are included -
Sku: 71028
Rubber Pad, Wavemaster 7000 (ver. 2)
This rubber pad fits in between the motor and the steel base on the Wavemaster 7000 (version 2) and provides a buffer against vibrations This is one of two rubber pads that mount on the steel base The second is under the base between the base and the floor ...read more -
Sku: 70945
Gasket, Impeller Screw Wavemaster 9000
This little gasket fits over the impeller screw and is snugged into place against the impeller when the screw is tightened -
Sku: 30548
Starite Compression Fitting, 1-1/2″
1-1/2" compression coupling assembly (pump union) for all Starite pumps used on Hot Spring spas -
Impeller for the Wavemaster 9000 jet pump This 2 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads
-
This stainless steel impeller screw (left-hand threads) screws onto the end of the motor shaft to secure the impeller from spinning off of the Sta-rite Maxi-Glass 1hp & 2hp pumps that were used in Hot Spring spas prior to 1994
-
Sku: 70399
Seal Plate, Wavemaster 7000 (v.1)
The seal plate is the half of the "wet end" on the 1st version Wavemaster 7000 that bolts onto the pump motor -
Seal Plate for the Wavemaster 7000 version 2 and the Wavemaster 9000
-
Jet pump motor for the Wavemaster 7000 version 2 Specs: HP: 1 0 Frame: 48Y Voltage: 115/230 Speed: 1 Amperage: 7 0/14 0 SF: 1 65 Hz: 60 Base: Steel Reference: TPEE-WK03
-
Jet pump motor for the Wavemaster 9000 version 2 Specs: HP: 2 0 Frame: 48Y Voltage: 230 Speed: 1 Amperage: 11 2 SF: 2 60 Hz: 60 Base: Plastic Reference: TPEG-WK02
-
Pump Shroud Air Vent for Wavemaster 7000 version 2 and Wavemaster 9000
-
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment
-
Sku: 70411
Tailpiece, Wavemaster 7000 (version 1)
Inside piece of the 2" compression fitting for a Wavemaster 7000 (v 1 and v 2) and a Wavemaster 9000 -
Sku: 10408
Receptacle, Jet Pump, Hot Spring
This jet pump receptacle mounts into the control box to provide an outlet to plug in the jet pump's power cord on the 1990-1996 Hot Spring Classic, Grandee, Highlife, Jetsetter, Prodigy & Sovereign spa models -
Wavemaster 7000 (v 1) suction cover (volute) is the front half of the "wet end" (suction side) It has a square flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996
Showing 61–90 of 148 results