It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Get important tools and hardware you need to maintain or fix your spa. This includes Screws, Bolts, Washers, Hose Clamps, Nuts, Power Cables, Silicone, Glue, Foam, Wrenches, Pliers, Custom Tools, and more.
Showing 1–30 of 35 results
-
Sku: 73223-Screw-BYP
Screw, Front Cover of IQ 2020 Control Box
Screw, Front Cover of IQ 2020 Control Box (THPH SS 8-32X3/8') -
Sku: 30413
Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate
-
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment
-
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more
-
Sku: 72574
Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 1178401
Limelight Point of Light Removal Tool
This is the tool used to remove and reinstall the Points of Light LEDs used in Limelight brand spas -
Sku: 30099
Bushing, Strain Relief
This 3/8" strain relief is used to secure the jet pump(s), circulation pump, light and Ozonator power cords to the bottom of the IQ 2020 Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should ...read more -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP
-
Sku: 36586
Clip, Extruded Air Valve
Used to hold the air intake for the Freshwater II Ozonator in place on the wall in the equipment compartment near the Ozonator Found in Hotspring and Tiger River Spas with Freshwater II Ozonators -
Impeller screw for the Wavemaster 7000 (v 1) This screw is reversed thread (left hand thread) This screw is not needed if you are purchasing a new impeller 2014 forward
-
Sku: 72714
Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Sku: 73451
Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Sku: 72715
Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
Sku: 71744
Washer, Gliderite
These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor
-
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump
-
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1)
-
Sku: 33366
Screw, #8-32 X 3/8in Hex Washer-Hd
The screw used on the Freshwater II Ozonator -
Sku: 70973
Ozone Injector Bypass Tool
Ozone injector bypass tool -
Sku: 75105
Hardware Bag #4 for Upright Cover Lifter
Hardware for the upright spa cover lifter -
Sku: 56WUA500-V
Wavemaster 9000/9200, 8000/8200 Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 56-frame LX wet ends item 77713 and 77712 -
Sku: 48WUA-V
Wavemaster Volute O-Ring
LX MODEL O-RING Replacement volute o-ring (largest o-ring) for the Wavemaster pumps with vendor number 3536 (LX) This o-ring fits the 48-frame LX wet ends item 77711, 77710, and 77709 Stamped on wet-end: PP-GF30; B436-14 (03) Reference models (see ...read more -
Sku: 70404
Diffuser Screw, 8-32 X 1in Phillips, Wavemaster 7000 V1
This item is obsolete and replaced by:
70951Obsolete: Factory replacement suggestion item 70951 This is the screw that secures the diffuser to the seal plate on a Wavemaster 7000 (v 1) pump -
Sku: 33144
Kepnut, 8-32 SS
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Use on the Freshwater II Ozonator -
Sku: 33974
Screw, 8-32 X 3/8in SS
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Used on the Freshwater II Ozonator -
Sku: 34018
Kepnut 10-24 SS
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Used on the Freshwater II Ozonator -
Sku: 71105
Bracket, Corner (G/K)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Bracket, Corner (G/K) -
OBSOLETE-Use the 71107-BYP
-
Sku: 71110
Screw, #10 X 1-1/2in
Obsolete from the factory -Available at most hardware stores 1-1/2in Phillips flat head screw that attaches the side hinge base to the spa cover
Showing 1–30 of 35 results