I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Get important tools and hardware you need to maintain or fix your spa. This includes Screws, Bolts, Washers, Hose Clamps, Nuts, Power Cables, Silicone, Glue, Foam, Wrenches, Pliers, Custom Tools, and more.
Showing all 23 results
-
Sku: 30018
Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 70035
Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059
Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Sku: 30297
Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate
-
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment
-
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more
-
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP
-
Sku: 30396
Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 36586
Clip, Extruded Air Valve
Used to hold the air intake for the Freshwater II Ozonator in place on the wall in the equipment compartment near the Ozonator Found in Hotspring and Tiger River Spas with Freshwater II Ozonators -
Sku: 73249
Panel Clips, Male and Female, QTY 4
Panel clips, male/female, for the removable panels on Hot Spring models, quantity of 4 -
Sku: 10057
Jet Spanner Wrench
Service Tool: This spanner wrench is designed to expand to the desired width and insert into the indentations on the outside ring of various jet wall fittings -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment
-
Non-metallic hinge for all pre-1995 wooden Hot Spring equipment compartment doors (access doors)
-
Sku: 50554
Spanner Wrench Air Valve
Spanner wrench air valve -
Sku: 20018
Hinge, 7in
This door hinge was used on the Hot Spring spas -
Sku: 71066
Flow Tool
This flow tool is used to determine if the circulation pump flow is adequate to keep the spa from tripping the heater high-limit One end of this tool is used to unscrew the perforated drain grate and the other end is inserted into the drain The flow of ...read more -
Sku: 70825-BYP
Snap Ring Pliers Tool, Smart Jet Diverter Valve
These snap ring ("c"-ring) pliers can be used to remove the snap ring on Smart Jet diverter valves (71494, 71495, 73768, 73769) found in most hot tubs Made of carbon steel and vinyl grip handles and comes with interchangable straight, 45 degree and 90 degree ...read more -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1)
-
Sku: 50017
Red Devil Scraper, 3010
Red Devil scraper, 3010 -
This nut goes onto the volute bolt that secures the seal place to the volute
-
Sku: 71703
Spanner Wrench 3.6 in diameter
Spanner wrench 3 6 inch in diameter -
Sku: 70102
Jet Retainer Tool
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Spanner tool used on the pre-1990 Hot Spring Watkins fixed jets to tighten the retainer around the jet ...read more
Showing all 23 results