I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Get important tools and hardware you need to maintain or fix your spa. This includes Screws, Bolts, Washers, Hose Clamps, Nuts, Power Cables, Silicone, Glue, Foam, Wrenches, Pliers, Custom Tools, and more.
Showing 1–30 of 48 results
-
Sku: 300055
Spring Clamp, 3/4 inch
3/4" spring clamp (aka wire clamp) is used to secure the 3/4 inch vinyl tubing (70315) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to ...read more -
Sku: 73019
Pillow Retainer Screw Kit
The plastic retainers in this kit come in two lengths: The short gray retainers are used if your pillows have remained in place over the years The gray extensions are used only if your pillows have fallen off often in the past -
"Blade Mount" pillow retainer (set of two blades) for all Hot Spring spa pillows and all Limelight spa pillows beginning in the second quarter of 2007 Check the diagrams for the correct pillow retainer
-
Sku: 31134
Spring Clamp, 1/4in
Used to secure 1/4" (ID) vinyl tubing 70318 (OD measure 7/16") to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this ...read more -
Sku: 30413
Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 31228
Spring Clamp, 1/2in
1/2" spring clamp for securing 1/2" ID vinyl tubing (70316) to components Item 70316 has an inner diameter of 1/2" and an outer diameter of 3/4" This clamp fits the 3/4" OD Note: Wear eye protection when squeezing these little rascals Service techs ...read more -
Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps used on Hot Spring models prior to 1993
-
Sku: 70396
Washer, Flat 3/8in Wavemaster
Flat 3/8in washer -
Sku: 34465
Spring Clamp, 3/8in
3/8" spring clamp (aka wire clamp) is used to secure the 3/8 inch vinyl tubing 70317 (9/16" OD) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers are hose clamp ...read more -
Sku: 72574
Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 73557
Screw Cover Cream
Six of these screw covers are used to hold the equipment door in place on the Hot Spot TX from 2005 to 2010 These cream-colored caps attach to a plastic retainer that surrounds the head of the screw used to hold the door panel in place to provide a more ...read more -
Sku: 300602
Spring Clamp, 1in
1" spring clamp (wire clamp) used to secure 1" vinyl tubing -
Sku: 72714
Hardware Bag #2, Cover Cradle II
This Cover Cradle II hardware bag #2 includes the following: 1/4"-20 x 3/4" Stainless Steel Hex Bolts (Qty 4) #10 x 1-1/2" Stainless Steel Flat Head Screws (Qty 8) #10 x 1-1/2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware ...read more -
Sku: 71893
Screw Cover, Equipment Door, TX, Taupe
Six of these round screw covers are used on the Solana TX made from 2000-2004 to hold the equipment door in place These taupe-colored caps attach to a plastic retainer that surrounds the head of the screw used to hold the door panel in place to provide a ...read more -
Sku: 30407
Washer, Nylon Flt (Thin)
Nylon washer for the jet selector water diver valve on all Hot Spring & Tiger River spa models manufactured prior to 1994 -
Sku: 30105
Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Lock washer for the diffuser screw on a Wavemaster 7000 (ver 2) and Wavemaster 9000 jet pump
-
Flat Volute washer for the Wavemaster 7000 version 2 and he Wavemaster 9000
-
Solid Wood Corner Brace with two vent holes - Hot Spring Spa This solid wood corner brace replaces either the front left/right corner brace which has two ventilation holes for the jet pumps The corner brace should be treated or painted, prior to ...read more
-
Sku: 71744
Washer, Gliderite
These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter -
Sku: 71072
Retainer Clip
Used on the 1995-1999 Hot Spring Dream Pillow Neckjet -
Sku: 33570
Washer, #10 .200 X .359 X .063
Washer, #10 200 X 359 X 063 -
Mounting plate found on the backside of all 1994-1997 Hot Spring Classic spas control panels
-
Sku: 35243
Skimmer Backing Plate, Hot Spot 2
This is the backing plate for the skimmer on all 1995-1997 Hot Spot2 spa models -
One of two volute washers on the Wavemaster 7000 (second version) and the Wavemaster 9000 jet pump
-
Sku: 50051
Plier Clamp
Plier clamp -
Sku: 76099
Screw Cap, Black set of 10
CAP, SCREW BLACK 10/SET RTA -
This diffuser lock washer is used with the screws and nuts that belong to heater 20286 50-BYP and 20286 75-BYP
-
Obsolete: Factory replacement suggestion item #72714 Hardware Bag #2 used on the Cover Cradle and Cover Cradle II It contains screws for mounting the cover lifter to the spa and cover All screws use Robertson (square drive) head bits
-
Sku: 30410
Washer, Brass Flt 1/4in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Washer, Brass Flt 1/4in
Showing 1–30 of 48 results