It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Brand: Cover Cradle I, Freshwater Ozonator System, Iq 2020, Multizone Lighting, Starite
Showing 1–30 of 44 results
-
Sku: 73223-Screw-BYPScrew, Front Cover of IQ 2020 Control Box
Screw, Front Cover of IQ 2020 Control Box (THPH SS 8-32X3/8') -
Sku: 31134Spring Clamp, 1/4in
Used to secure 1/4" (ID) vinyl tubing 70318 (OD measure 7/16") to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this ...read more -
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 30413Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 70035Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70036Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 30297Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Sku: 30220Volute O-Ring, Starite
Volute O-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993 -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
Sku: 72574Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 30099Bushing, Strain Relief
This 3/8" strain relief is used to secure the jet pump(s), circulation pump, light and Ozonator power cords to the bottom of the IQ 2020 Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should ...read more -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP -
Sku: 36586Clip, Extruded Air Valve
Used to hold the air intake for the Freshwater II Ozonator in place on the wall in the equipment compartment near the Ozonator Found in Hotspring and Tiger River Spas with Freshwater II Ozonators -
Sku: 74888-1Multizone Lighting Bayonet Sleeves
Multizone lighting bayonet sleeves, quantity of 1 -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment -
Sku: 33366Screw, #8-32 X 3/8in Hex Washer-Hd
The screw used on the Freshwater II Ozonator -
Multizone lighting, LED Sleeve, Bayonet LED (pack of 25) KIT SLEEVE, BAYONET LED For a quantity of 1, use 74888-1 -
This diffuser lock washer is used with the screws and nuts that belong to heater 20286 50-BYP and 20286 75-BYP -
Obsolete: Factory replacement suggestion item #72714 Hardware Bag #2 used on the Cover Cradle and Cover Cradle II It contains screws for mounting the cover lifter to the spa and cover All screws use Robertson (square drive) head bits -
Sku: 33144Kepnut, 8-32 SS
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Use on the Freshwater II Ozonator -
Sku: 33974
Screw, 8-32 X 3/8in SS
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Used on the Freshwater II Ozonator -
Sku: 34018
Kepnut 10-24 SS
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Used on the Freshwater II Ozonator -
Sku: 71105
Bracket, Corner (G/K)
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Bracket, Corner (G/K) -
OBSOLETE-Use the 71107-BYP -
Sku: 71220
Nut, Slot 1/4in
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com -
Obsolete: Factory replacement suggestion item 75149 This kit (item#7 in the diagram) includes the following parts for the Cover Cradle: 1/4" Ball Stud X 4 1/4" Split Lock Washer X 2 1/4" Slot Nuts X 2 1/4" Nut
-
Sku: 71215Screw, 1/4-20 x 3/4in for Side Hinge
Obsolete from the factory -Available at most hardware stores This #20 1/4in x 3/4" standard screw (stainless steel) that secures the sidearm to the base hinge
Showing 1–30 of 44 results