quick ship ,as described and was perfect transaction. ThanksOn 06/13/2024 by B. H. (verified customer)
Brand: Hot Spot, Hot Spring Pre 89, Wavemaster 4000
Showing 1–30 of 146 results
-
Sku: 300055Spring Clamp, 3/4 inch
3/4" spring clamp (aka wire clamp) is used to secure the 3/4 inch vinyl tubing (70315) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to ...read more -
Sku: 73019Pillow Retainer Screw Kit
The plastic retainers in this kit come in two lengths: The short gray retainers are used if your pillows have remained in place over the years The gray extensions are used only if your pillows have fallen off often in the past -
"Blade Mount" pillow retainer (set of two blades) for all Hot Spring spa pillows and all Limelight spa pillows beginning in the second quarter of 2007 Check the diagrams for the correct pillow retainer -
Sku: 34878O-Ring, Control Thermistor
Control Thermostat Thermistor o-ring for the 79006 and 78970 thermistors This o-ring is located on the "inlet" side of the heater and is the larger of the two thermistor o-rings For the outlet side of the heater see the part# 34879 o-ring -
Sku: 34879O-Ring, Hi-Limit Thermistor
High-Limit Thermistor o-ring for the 79005 and 78969 thermistors This o-ring is located on the "outlet" side of the heater and is the smaller of the two thermistor o-rings For the "inlet" side of the heater see part 34878 -
Sku: 31134Spring Clamp, 1/4in
Used to secure 1/4" (ID) vinyl tubing 70318 (OD measure 7/16") to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers or hose clamp pliers to squeeze, then slide this ...read more -
Sku: 37112O-Ring, Precision Jet
Precision Jet o-ring fits between the interior spa shell and the wall fitting nut to prevent leaks from around the jet The o-ring creates a seal between the jet body and the back of the shell when compressed by the wall fitting nut -
This stainless steel screw is used to secure the Moto-Massage faceplate to its guide body on many Hot Spring and Solana spa models Also used on the 1995-1999 Hot Spring Dream Pillow Jet Check your serial number in the parts finder to be sure this part ...read more -
Sku: 71410-BYPVolute O-Ring, Wavemaster
This is the largest O-ring used on the current Wavemaster series of wet ends for Hot Springs, Tiger River, Limelight, Solana and Hot Spot model spas This o-ring fits between the suction cover and the volute of the pump series: XP2/XP2E This o-ring is only ...read more -
Sku: 71554Wavemaster Volute O-Ring
GECKO MODEL O-RING Replacement o ring (largest o-ring) for the Wavemaster 4000, 6000, 8000 (ver 3), 8200, 9000 (ver 3), 9200 jet pumps Will fit on pump series: XP2/XP2e -
Sku: 30240Volute O-ring, Wavemaster
Large o-ring that fits in between the two halves of the "wet end" (volute & volute cover) of the FMHP Series Wavemaster 3000, Wavemaster 5000 & Wavemaster 8000 jet pumps -
GECKO MODEL SCREW This stainless steel screw is used to attach the volute cover to the volute on most Wavemaster jet pumps -
Sku: 34447-x2-BYPCompression Fitting O-rings, for 2 inch Union (Qty of 2)
(Quantity of 2 o-rings) O-rings used on the pumps 2" compression fittings ( 71036 ) found on most Hot Spring, Tiger River, Limelight, Hot Spot and Solana spa models Also used on the replacement "Wet End" pump kits and some heaters The 2" measurement refers ...read more -
O-ring used on the 2" compression fittings (71036) on most Hot Spring, Tiger River, Hot Spot, and Solana spa models The 2" measurement refers to the inner diameter of the most narrow part of the compression fitting/union The o-ring that is included measures ...read more -
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 30018Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 30413Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 31228Spring Clamp, 1/2in
1/2" spring clamp for securing 1/2" ID vinyl tubing (70316) to components Item 70316 has an inner diameter of 1/2" and an outer diameter of 3/4" This clamp fits the 3/4" OD Note: Wear eye protection when squeezing these little rascals Service techs ...read more -
This is the largest o ring on the Wavemaster 7000 (v 1) jet pump It fits between the cover and the seal plate -
Sku: 70035Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70036Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70396Washer, Flat 3/8in Wavemaster
Flat 3/8in washer -
Sku: 30297Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Sku: 30220Volute O-Ring, Starite
Volute O-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993 -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate -
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
This o-ring fits onto the front of the diffuser on the Wavemaster 7000 (v 1) jet pump and also between the suction flange and the suction cover on the front of the pump
Showing 1–30 of 146 results