Super service. Thank you.On 05/21/2024 by N. M. (verified customer)
Brand: Aqua Comb, Hot Spring Pre 89, Wavemaster 3000
Showing 31–60 of 168 results
-
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
This o-ring fits onto the front of the diffuser on the Wavemaster 7000 (v 1) jet pump and also between the suction flange and the suction cover on the front of the pump -
Sku: 33850Screw, 8-16 X 1/2in
This screw is used on various air controls and water diverter valve levers & bezels -
Sku: 34465Spring Clamp, 3/8in
3/8" spring clamp (aka wire clamp) is used to secure the 3/8 inch vinyl tubing 70317 (9/16" OD) to various components Note: Wear eye protection when squeezing these little rascals Service techs typically use either needle-nose pliers are hose clamp ...read more -
There were two different sized ball studs used on Hot Spring cover lifters One is this 1/4" threaded shaft and the other (3rd qtr 2009) is 5/16" threaded shaft (part 75149) Either one size or the other will be on your cover lifter but not both sizes Ball ...read more -
Sku: 30348Screw, #10-24 X 3/4in Stainless Steel
Stainless steel screw mostly used on the 1980-1994 115volt Hot Spring heaters to secure the heater element to the heater body Four of these are used with each heater -
Sku: 72574Hardware Bag #1, Cover Cradle
This Cover Cradle & Cover Cradle II hardware bag #1 includes the following: Four Hole Side Hinge (Qty 2) Four Hole Rear Hinge (Qty 2) #10 x 1" Flat Head Screws (Qty 8) #10 x 1-1/2" Flat Head Screws (Qty 8) Note: The items in this hardware bag are ...read more -
Sku: 302637Door Screw, Hot Spot
This screw is used to attach the door(s) on all Hot Spot spas beginning in 2003 that use wood or synthetic wood siding: 1/4-20 x 1-3/4" Truss stainless steel Phillips head screw Price is per individual screw This part number replaces the obsolete 1-1/2" ...read more -
Sku: 36153O-Ring, Front Wallfitting
Used on the Soothing Seven Jet and various other jets -
Sku: 36534Gasket, Jet Face
This black rectangle rubber gasket fits inside of the jet face on Hot Spring, Tiger River, Hot Spot, and Solana spa models This gasket creates the seal for the air adjustment of the jet This gasket failing will not cause the spa to leak -
Sku: 30392Nut, Hex #10-24in Stainless Steel
Used on the 1980-1994 115volt Hot Spring heaters in conjunction with the stainless steel screw (30348) to secure the heater element to the heater body -
Sku: 36535Gasket, Soothing Seven Jet
Soothing Seven rectangle jet gasket This gasket is included when purchasing the Soothing Seven jet face -
Sku: 33832O-Ring, Air Control .737 X .103
One of two air control piston o-rings on 1993-2003 Hot Spring and 1999-2003 Tiger River spa models (2nd o-ring is part 33831) -
Sku: 30356Nylon Screw, Control Panel, Hot Spring
Nylon screw used to secure the control panel (70275) in place on all 1989-1993 Hot Spring spa models The nylon screw threads into the actual control box so it is critical to use a non-conductive material to prevent an electrical short in the control box from ...read more -
Sku: 33831O-Ring, Air Control Piston .612 X .103
O-ring for the air control piston in all 1993-2003 Hot Spring and 1999-2003 Tiger River spa models (2nd o-ring is part 33832) -
Largest o ring on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump seal plate -
Sku: 31983Control Air O-Ring
Large o-ring used under the bezel on the 1989-1993 Hot Spring air control valves -
Sku: 300040Brass Door Screw Insert, 1/4in
This brass insert is used on the door frames of various spa models to provide attach a door using a stainless steel screw which screws into this insert -
O-ring that mounts onto the front of the pump diffuser -
Stainless steel screw used to secure the heater to the equipment compartment floor on Hot Spring & Tiger River spa models Also used on the SilentFlo 5000 Circulation pump and to hold the Ozonator to the wall of the equipment compartment -
Sku: 30099Bushing, Strain Relief
This 3/8" strain relief is used to secure the jet pump(s), circulation pump, light and Ozonator power cords to the bottom of the IQ 2020 Control boxes The strain relief prevents the cord from accidentally being disconnected from inside the control box should ...read more -
This screw is used to hold the front cover of the IQ 2000 and IQ 2020 box in place This screw is not compatible on models made between 2007 and 2009 5 or older models with the upgraded heater relay board (Item #77119) The screw is too long and will hit ...read more -
This ball stud is found on 3rd quarter 2009 and newer UpRite, Cover Cradle and Cover Cradle II lifters The older cover lifters used a 1/4" threaded shaft ball stud which is part# 71107-BYP -
Sku: 10437O-Ring, Wall Fitting
Silicone (rubber will break down in chlorinated water) o-ring to seal the wall fitting nut against the spa shell The wall fitting nut screws into the jet body that's located on the back of the spa shell -
Sku: 31185Air Valve O-Ring, .612 X .103
Small interior o-ring used on the 1989-1993 Hot Spring air control valves -
Sku: 30334Screw, #4 X 1/2in Stainless Steel
Stainless steel screw used in various locations on Hot Spring, Tiger River, Solana, Hot Spot and Limelight spas -
Sku: 32310Air Valve O-Ring, Hot Spring
Large o-ring used on the 1989-1993 Hot Spring air control valves -
Sku: 30396Nut, #1/4in-20in Stainless Steel
Stainless steel nut used to secure the 220 volt Hot Spring heater elements (31409-BYP) to the heater housing (70192) -
Sku: 30402Brass Door Frame Insert, #20 X 1/4in
This brass insert is used on the equipment door's frame to provide a place for the door screws to secure the equipment door into place This part is used on all 1989-2007 Hot Spring spa models (except the Classic) and all Tiger River spas -
Sku: 30343Screw, #8 X 7/8in
Stainless steel screw for the jet selector water diverter valve lever on all Hot Spring spa models manufactured prior to 1994 that have a jet selector
Showing 31–60 of 168 results