Purchased the mother board for our 2006 hot springs Vanguard. Watched the video that Paul made in the installation. He goes over everything you need and the process along the way. Makes the task so effortless. I did the change out over a weekend and had a question. Email BackYardPlus and got a very fast response from Craig. I can’t say enough about the friendlyness, knowledge this company has. Will always be getting my parts from BackYardPlus. Saved me $$$ for sure. Again thank you Paul & Craig.On 03/21/2024 by C. S. (verified customer)
Showing 91–120 of 172 results
-
Sku: 71525
Silicone, DOW 732 Clear, 3 oz.
100% clear silicone used to waterproof around various water features above the water line of the spa This item is available from most hardware stores for about the same price -
Sku: 72017
Fastener, LED Light (Qty 4)
Fasteners used to hold the housing for the LED light assembly in place on Hotsprings, Tiger River, and Limelight spas These are included if you purchase a replacement light assembly -
This screw is used for holding the IQ 2000 and IQ 2020 control boxes in place on the mounting bracket in Hotsprings, Tiger River, and Limelight spas
-
Sku: 36018
IQ Control Box Bracket
This aluminum bracket attaches to the spa door frame to enable the IQ Control Box to mount securely to this bracket The bracket does not come with the two 36898 screws that attach it to the control box Simple wood screws are used to attach it to the wood ...read more -
This screw was used to hold the thermostat knob in place on the topside control panel used on Tiger River spas from 1992 to 1994 and the round-shaped air control knob on air valves used on Hotspring spas from 1989 to 1993 5
-
Sku: 30120
Lug, Grounding
Used on various components in the equipment compartment to provide a place for the grounding wire to attach to -
Sku: 30105
Romex Clamp 3/4in
This clamp is used as strain relief is used to secure the heater's power cord to the bottom of the IQ Control box The strain relief prevents the cord from accidentally being disconnected from inside the control box should the cord be pulled down -
Non-metallic hinge for all pre-1995 wooden Hot Spring equipment compartment doors (access doors)
-
Sku: 34304
Standoff, #10 – 32 X 1/2in
This standoff is found on the backside of the 1994-1997 Hot Spring control panels -
Sku: 50554
Spanner Wrench Air Valve
Spanner wrench air valve -
Sku: 73451
Hardware Bag #1, Uprite Cover Lifter
Bag #1 for the upright cover lifter Contains the following: 2 x 1/4 x 20 5/8" Hex Bolts 2 x 1/4 x 1" Fender Washers 2 x 2 Hold Deck Hinge 10 x #10 Washers 8 x #10 1/2" Square Panhead Self Tapping Screws 10 x #10 1 1/2" Square Pan Tapping Screws 12 ...read more -
Lock washer for the diffuser screw on a Wavemaster 7000 (ver 2) and Wavemaster 9000 jet pump
-
Sku: 20018
Hinge, 7in
This door hinge was used on the Hot Spring spas -
Sku: 70946
Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Flat Volute washer for the Wavemaster 7000 version 2 and he Wavemaster 9000
-
Sku: 71066
Flow Tool
This flow tool is used to determine if the circulation pump flow is adequate to keep the spa from tripping the heater high-limit One end of this tool is used to unscrew the perforated drain grate and the other end is inserted into the drain The flow of ...read more -
Sku: 73493
Bartop Crack Repair, Hot Spring
This crack repair kit is used to heal a crack 6" or less on the backside of the spa This kit requires a working temperature of above 50 degrees for at least twenty-four hours during the curing process of the epoxy It is important to have clear access to the ...read more -
Sku: 73740
Leak Detection Kit
For Technicians Only Leak detection kit for Hot Spring, Hot Spot, and Limelight models -
Sku: 70825-BYP
Snap Ring Pliers Tool, Smart Jet Diverter Valve
These snap ring ("c"-ring) pliers can be used to remove the snap ring on Smart Jet diverter valves (71494, 71495, 73768, 73769) found in most hot tubs Made of carbon steel and vinyl grip handles and comes with interchangable straight, 45 degree and 90 degree ...read more -
Sku: 30399
Insert, Door, Classic F
-
Sku: 73789
Adhesive (DP 601 NS)
This is Scotch Guard Urethane Adhesive used to repair missing slats from all spa cabinets Due to the high price of this product, and special application gun needed to use it, we recommend the use of Power Grab Heavy Duty Construction Adhesive instead ...read more -
Sku: 73374
Stain Espresso
This stain is used on Hot Springs, Hot Spot, and Tiger River Spas It's used on spas with a synthetic espresso colored cabinet and is used to stain the areas of real wood that might be exposed in the equipment compartment to match the color of the synthetic ...read more -
Sku: 73256
Clarion Brackets
These brackets are used to mount the Clarion Light Bars to the spa or step or where ever desired Five sets of left and right pairs are included in each pack -
Sku: 72715
Hardware Bag #3, Cover Cradle II
This Cover Cradle II hardware bag #3 is only for spas with removable exterior panels and includes the following: #10 x 2" Stainless Steel Flat Head Screws (Qty 8) #10 x 2" Stainless Steel Pan Head Screws (Qty 14) Note: The items in this hardware bag are ...read more -
Sku: 71744
Washer, Gliderite
These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor
-
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump
-
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1)
-
Phillip head stainless steel screw, 8-18 x 3/8in for control panels on Hot Spring models 1994-1997
-
Sku: 33368
Screw, 10-32 x 3/8in
This screw is used on Hotsprings Spas made from 1994 to 1996 to hold the plastic stand-off in place on the mounting plate from behind This stand-off accepts the screws from the front of the control panel that are used to hold the control panel in place
Showing 91–120 of 172 results