quick ship ,as described and was perfect transaction. ThanksOn 06/13/2024 by B. H. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Brand: Solana | Plumbing: Barbed Adapter, Cap, Check Valve, Reducer
Showing 1–30 of 39 results
-
Sku: 1044101-72228-AM-BYPTubing Kit, Del-Ozone-1/4in with Check valve
This 1/4" ID (3/8" OD) ozone-resistant tubing works with UO3 ozone generator It includes an attached 1/4" ozone-resistant check valve, clamps, mounting screws, and new flag terminals This assembly is approx five feet in length Note: There is a small ...read more -
Sku: 1044101-72228-BYPTubing Kit, Freshwater III Ozonator-1/4in Tygon/Kynar with Check valve
This 1/4" ID (3/8" OD) Kynar/Tygon ozone-resistant tubing kit comes standard with the Freshwater III Ozonators It is the replacement for all Freshwater 3 ozonators It includes an attached 1/4" ozone-resistant check valve This assembly is approx six feet ...read more -
Sku: 35233Water Check Valve, 3/4 inch
This 3/4" water check valve is installed in the inlet side of the circulation pumps plumbing to prevent the backflow of water through the circulation pump once the jet pump is activated All water check valves have arrows stamped on the outside to indicate ...read more -
Air check valve for Hot Spring, Tiger River, and Hot Spot spa models This check valve is located in the equipment compartment under the bartop Its primary function is to prevent water from back flowing into the equipment compartment should a hydrotherapy ...read more -
Sku: 30700Cap, Drain Valve – 3/4in with Washer
Black 3/4" hose bib thread cap used on the drains of 1993 forward Hot Spring, Tiger River, Hot Spot, and Solana, and Limelight spa models It also includes the washer This cap is used both on the "Primary" Drain Valve, and the "Secondary" Drain Valve -
Sku: 38390Check Valve, Air, with Ball 1/2in
It is used to prevent water from backing into the airlines when the jets are off It is at the back of the Moto-Massage housing and glued into a 90-degree elbow It is also on the jetstream jets -
Sku: 1044101Check Valve (Ozone) Freshwater Ozone, 1/4in O.D.
Over time an Ozonator check valve will breakdown under the harsh conditions of ozone Our OEM check valves have a special diaphragm (Viton) that enables them to last longer than rubber Rubber diaphragms last about a month before the rubber becomes hard -
This air check valve is located in the equipment compartment, up high, under the bar top If a hydrotherapy jet should become obstructed (like when a guest sticks their finger in the jet), this item becomes critical in preventing water from back flowing into ...read more -
Sku: 72701Hartford Loop Assembly
This retrofit kit is used to replace the air check valve that was used in some Hot Spring spa models This kit replaces the obsolete 72342 Check your serial number in the parts finder above to be sure this part is for your spa -
This "Jet System" check valve is used on all Hot Spring models and all Tiger River spas This check valve engages when the diverter valve is changed to different positions For convenience, the inside diameter of this check valve is 1-1/2" and the outside ...read more -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system or jets in a Hot Spring & Tiger River spa It simply glues into a 1/2" PVC coupling or elbow with regular PVC cement -
Sku: 010009Barbed adapter 1 in x 3/8 Spigot
Barbed adapter 1 inch by 3/8 inch 425-5010 BARB ADAP 1IN(1)3/8IN -
Sku: 71981Check Valve, with Spring, 1-1/2in
1-1/2" spring style check valve is commonly found between the jet pump and filter housing on Tiger River spas This check valve automatically closes when the Tiger River spas jet pump is turned off so the circulation pump (Silentflo 5000) can then draw water ...read more -
Barbed adapter which is 1/2" male threads on one end and 1/2" barbed on the other -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system of Hot Spring spa models -
Reducer Bushing, 3/4" Spig x 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 3/4" female slip fitting The connection should be made using PVC primer and cement -
Sku: 31288Reducer, 2in X 1-1/2in Spig X Slip
Reducer Bushing, 2" Spig x 1-1/2" Slip This bushing allows for a 1 1/2" male slip fitting or PVC pipe, rigid or flexible, to connect to a 2" female slip fitting The connection should be made using PVC primer and cement -
Reducing Bushing, 1"Spig X 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement -
Sku: 70173Check Valve (Water) 1/2in
This 1/2" water check valve is used on the discharge side of the old Laing circ pumps in pre-1990 Hot Spring 115volt Sovereign, Classic, Prodigy & Jetsetter models This is for 1/2" plumbing If your plumbing is 3/4" then use part 35233 -
Reducer Bushing, 1" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement -
Barbed adapter which is 3/4" male threads on one end and 1/2" barbed on the other -
Sku: 30667Coupling, Reducer 1in X 3/4in Sxs
This adapter is used to join a 3/4" PVC male fitting and a 1" PVC male fitting together PVC primer and cement should be used to adhere the fittings -
Sku: 37681Red Bushing, 2in X 3/4in (437-248)
Reducer Bushing, 2" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 2" female slip fitting The connection should be made using PVC primer and cement -
Sku: 30694Cap, 2in Slip
This is a cap that can be used to cap off a 2" male slip fitting or a 2" PVC pipe, either rigid or flexible PVC primer and PVC cement should be used to attach this fitting -
Sku: 30693PVC Cap 1 1/2in Slip
This is a cap which can be used to cap off a 1 1/2" male slip fitting or a 1 1/2" PVC pipe, either rigid or flexible PVC primer and PVC cement should be used to attach this fitting -
Reducer Bushing 1-1/2" Spig x 3/4 female iron pipe thread This bushing allows a 3/4" male pipe threaded fitting to be adapted to fit in a 1 1/2" female slip fitting The connection should be made using PVC primer and cement on the slip portion of the ...read more -
Reducer Bushing, 1-1/2" Spig x 1-1/4" Slip This bushing reduces a 1 1/2" female slip fitting down to a 1 1/4" female slip fitting PVC primer and cement should be used to glue the bushing in place -
Reducer Bushing, 1-1/4" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1 1/4" female slip fitting The connection should be made using PVC primer and cement -
Sku: 30666Coupling, Reducer 3/4in X 1/2in Sxs
This is a PVC coupler that allows two PVC pipes to be joined together using PVC primer and cement One side of the coupler accepts a 1/2" PVC pipe, either rigid or flexible, and the other side accepts a 3/4" PVC pipe, either rigid or flexible -
Sku: 36958437-073, Red Bushing, 1/2in X 3/8in
Reducer Bushing, 1/2" Spig x 3/8" Slip This bushing allows a 3/8" male slip fitting or 3/8" PVC or vinyl pipe, rigid or flexible, to be adapted to fit in a 1/2" female slip fitting The connection should be made using PVC primer and cement
Showing 1–30 of 39 results