It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 131 results
-
Sku: 1044101-72228-AM-BYP
Tubing Kit, Del-Ozone-1/4in with Check valve
This 1/4" ID (3/8" OD) ozone-resistant tubing works with UO3 ozone generator It includes an attached 1/4" ozone-resistant check valve, clamps, mounting screws, and new flag terminals This assembly is approx five feet in length Note: There is a small ...read more -
Sku: 1044101-72228-BYP
Tubing Kit, Freshwater III Ozonator-1/4in Tygon/Kynar with Check valve
This 1/4" ID (3/8" OD) Kynar/Tygon ozone-resistant tubing kit comes standard with the Freshwater III Ozonators It is the replacement for all Freshwater 3 ozonators It includes an attached 1/4" ozone-resistant check valve This assembly is approx six feet ...read more -
Sku: 35233
Water Check Valve, 3/4 inch
This 3/4" water check valve is installed in the inlet side of the circulation pumps plumbing to prevent the backflow of water through the circulation pump once the jet pump is activated All water check valves have arrows stamped on the outside to indicate ...read more -
Air check valve for Hot Spring, Tiger River, and Hot Spot spa models This check valve is located in the equipment compartment under the bartop Its primary function is to prevent water from back flowing into the equipment compartment should a hydrotherapy ...read more
-
Sku: 36159
Precision Jet Elbow
This elbow is used to glue onto the rear of the Precision Jet Body This elbow is an odd size and is not available at the local hardware store -
Sku: 30237-x2-BYP
Compression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488
Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401
Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: 38390
Check Valve, Air, with Ball 1/2in
It is used to prevent water from backing into the airlines when the jets are off It is at the back of the Moto-Massage housing and glued into a 90-degree elbow It is also on the jetstream jets -
Sku: 1044101
Check Valve (Ozone) Freshwater Ozone, 1/4in O.D.
Over time an Ozonator check valve will breakdown under the harsh conditions of ozone Our OEM check valves have a special diaphragm (Viton) that enables them to last longer than rubber Rubber diaphragms last about a month before the rubber becomes hard -
Sku: 36160
Precision Jet Tee
This tee is used to glue onto the rear of the Precision Jet Body and provides a 1/2" connection on either side of the tee This tee is not available at the local hardware store -
This air check valve is located in the equipment compartment, up high, under the bar top If a hydrotherapy jet should become obstructed (like when a guest sticks their finger in the jet), this item becomes critical in preventing water from back flowing into ...read more
-
Sku: 72701
Hartford Loop Assembly
This retrofit kit is used to replace the air check valve that was used in some Hot Spring spa models This kit replaces the obsolete 72342 Check your serial number in the parts finder above to be sure this part is for your spa -
Sku: 70425
Bypass Tee
This assembly is found on all Tiger River spas This 3/4" x 1/2" tee has 3/4" male barbed fittings on each end and a 1/2" barbed male fitting on the elbow It is located in front of the circulation pump between the check valve (35233) and the inlet of the ...read more -
This "Jet System" check valve is used on all Hot Spring models and all Tiger River spas This check valve engages when the diverter valve is changed to different positions For convenience, the inside diameter of this check valve is 1-1/2" and the outside ...read more
-
45 degree PVC elbow, 2", Spg X Slip
-
Sku: 70864
Check Valve, Safety Suction
This check valve's function is to "open" when someone puts their hand over the jet pumps suction fitting within the filter intake This check valve will "open" drawing air into it from the equipment compartment, thereby stopping suction of the jet pump This ...read more -
Barbed tee 1/4" on all three sides Used with 1/4" vinyl tubing and 1/4" clamps
-
Sku: 71981
Check Valve, with Spring, 1-1/2in
1-1/2" spring style check valve is commonly found between the jet pump and filter housing on Tiger River spas This check valve automatically closes when the Tiger River spas jet pump is turned off so the circulation pump (Silentflo 5000) can then draw water ...read more -
Sku: 34838
Elbow 1/2in Polybarb
This is a 1/2" 90-degree barbed elbow for use with clear 1/2" PVC tubing -
Sku: 31487
Tee, 1/2in X 1/2in Barb
Tee, Barbed, Black Poly, 1/2" x 1/2" x 1/2" -
Sku: 34391
Elbow, Street 90 2in Spig X Slip
This is a 2" 90-degree street elbow made of PVC plastic It has a male PVC fitting on one side, and on the other side, it has a female PVC slip fitting This allows for the elbow to be used in tighter spaces -
Sku: 30642
Elbow, 90 Degree 1/2in Slip X Slip
This elbow is used to join two 1/2" male PVC slip fittings or 1/2" rigid or flexible PVC pipes together at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 30626
Tee, 1/2in Slip X Slip X Slip
This PVC tee will accept 1/2" male rigid or flexible PVC pipe or male PVC fittings 1/2" schedule 40 thick-walled clear vinyl PVC can also be glued directly to this fitting PVC primer and cement should be used on this fitting Failing to use primer ...read more -
Sku: 300843
406-101 Red Elbow 3/4inX1/2in
Reducing 90-degree ell, 3/4" x 1/2", plumbing fitting -
Sku: 31932
Elbow, 90 Degree 2in Slip X Slip
This elbow is used to join two 2" male PVC slip fittings or 2" rigid or flexible PVC pipes together at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 30643
Elbow, 90 Degree 3/4in Slip X Slip
This is a 3/4" 90-degree elbow made out of PVC which will accept two male 3/4" PVC flex or rigid pipes and join them together at a 90-degree angle using PVC primer and cement -
Sku: 33021
Elbow, 90 Degree 1-1/4in X 1in
This elbow is used to join a 1 1/4" male PVC slip fitting or 1 1/4" rigid or flexible PVC pipe to a 1" male PVC slip fitting or 1" rigid or flexible PVC pipe at a 90-degree angle PVC primer and cement should be used to secure this fitting to the fittings ...read more -
Reducer Bushing, 3/4" Spig x 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 3/4" female slip fitting The connection should be made using PVC primer and cement
Showing 1–30 of 131 results