It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 86 results
-
Sku: 74078
Injector, Freshwater Ozone, Black
The injector fits in-line after the Silentflo 5000 (discharge side and after the heater) This Kynar plastic "venturi" injector is ozone resistant and is used with the Freshwater III High Output Ozonator by Watkins manufacturing, item 72602 -
Sku: 74077
Injector, Freshwater Ozone, Red
This red ozone injector was used with the Freshwater I & Freshwater III (for Hot Spot & Solana spas) It is designed to allow a pre-determined amount of ozone bubbles per minute to enter the spa's circulating system The injector is matched to the ...read more -
Sku: 1044101-72228-AM-BYP
Tubing Kit, Del-Ozone-1/4in with Check valve
This 1/4" ID (3/8" OD) ozone-resistant tubing works with UO3 ozone generator It includes an attached 1/4" ozone-resistant check valve, clamps, mounting screws, and new flag terminals This assembly is approx five feet in length Note: There is a small ...read more -
Sku: 1044101-72228-BYP
Tubing Kit, Freshwater III Ozonator-1/4in Tygon/Kynar with Check valve
This 1/4" ID (3/8" OD) Kynar/Tygon ozone-resistant tubing kit comes standard with the Freshwater III Ozonators It is the replacement for all Freshwater 3 ozonators It includes an attached 1/4" ozone-resistant check valve This assembly is approx six feet ...read more -
Sku: 35233
Water Check Valve, 3/4 inch
This 3/4" water check valve is installed in the inlet side of the circulation pumps plumbing to prevent the backflow of water through the circulation pump once the jet pump is activated All water check valves have arrows stamped on the outside to indicate ...read more -
Air check valve for Hot Spring, Tiger River, and Hot Spot spa models This check valve is located in the equipment compartment under the bartop Its primary function is to prevent water from back flowing into the equipment compartment should a hydrotherapy ...read more
-
Sku: 38390
Check Valve, Air, with Ball 1/2in
It is used to prevent water from backing into the airlines when the jets are off It is at the back of the Moto-Massage housing and glued into a 90-degree elbow It is also on the jetstream jets -
Sku: 1044101
Check Valve (Ozone) Freshwater Ozone, 1/4in O.D.
Over time an Ozonator check valve will breakdown under the harsh conditions of ozone Our OEM check valves have a special diaphragm (Viton) that enables them to last longer than rubber Rubber diaphragms last about a month before the rubber becomes hard -
Sku: 36160
Precision Jet Tee
This tee is used to glue onto the rear of the Precision Jet Body and provides a 1/2" connection on either side of the tee This tee is not available at the local hardware store -
Air control valve piston for all 1993-2003 Hot Spring and 1999-2003 Tiger River spa models Reference: 33837
-
Sku: 73916
Air Control Valve Piston
The piston turns by the valve lever to increase or decrease the airflow to the jets It is used on Hot Spring, Tiger River, Hot Spot, Solana, and Limelight spa models -
This air check valve is located in the equipment compartment, up high, under the bar top If a hydrotherapy jet should become obstructed (like when a guest sticks their finger in the jet), this item becomes critical in preventing water from back flowing into ...read more
-
Sku: 72701
Hartford Loop Assembly
This retrofit kit is used to replace the air check valve that was used in some Hot Spring spa models This kit replaces the obsolete 72342 Check your serial number in the parts finder above to be sure this part is for your spa -
Sku: 70425
Bypass Tee
This assembly is found on all Tiger River spas This 3/4" x 1/2" tee has 3/4" male barbed fittings on each end and a 1/2" barbed male fitting on the elbow It is located in front of the circulation pump between the check valve (35233) and the inlet of the ...read more -
This "Jet System" check valve is used on all Hot Spring models and all Tiger River spas This check valve engages when the diverter valve is changed to different positions For convenience, the inside diameter of this check valve is 1-1/2" and the outside ...read more
-
Sku: 75003
Air Control, Piston/Driver
ON BACKORDER WITH NO CURRENT ETA - The main air control valve component regulates the airflow to the jets when the lever is turned on all 1989-1993 Hot Spring spa models -
Sku: 70864
Check Valve, Safety Suction
This check valve's function is to "open" when someone puts their hand over the jet pumps suction fitting within the filter intake This check valve will "open" drawing air into it from the equipment compartment, thereby stopping suction of the jet pump This ...read more -
Barbed tee 1/4" on all three sides Used with 1/4" vinyl tubing and 1/4" clamps
-
Sku: 71981
Check Valve, with Spring, 1-1/2in
1-1/2" spring style check valve is commonly found between the jet pump and filter housing on Tiger River spas This check valve automatically closes when the Tiger River spas jet pump is turned off so the circulation pump (Silentflo 5000) can then draw water ...read more -
Sku: 31487
Tee, 1/2in X 1/2in Barb
Tee, Barbed, Black Poly, 1/2" x 1/2" x 1/2" -
Sku: 30626
Tee, 1/2in Slip X Slip X Slip
This PVC tee will accept 1/2" male rigid or flexible PVC pipe or male PVC fittings 1/2" schedule 40 thick-walled clear vinyl PVC can also be glued directly to this fitting PVC primer and cement should be used on this fitting Failing to use primer ...read more -
Reducer Bushing, 3/4" Spig x 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 3/4" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 34458
Red Tee 2in X 1-1/2in X 1-1/2in
PVC tee, 2" X 1-1/2" X 1-1/2" slip -
Sku: 72185
Diverter valve Tee
Tee for 2 position diverter valve -
Sku: 32465
Tee 2in
This tee allows three 2" male PVC slip connections, or 2" PVC pipe (rigid or flexible) to be joined together, one of which is perpendicular to the other two connections PVC primer and glue should be used to adhere to the male connections tog the fitting -
Sku: 30681
Bushing, 1-1/2in X 1in Sp X Slip
This bushing is used to adapt a 1" male PVC slip fitting to fit in a 1 1/2" female slip fitting, or to allow a 1 1/2" female slip fitting to accept a 1" male slip fitting -
Sku: 34751
Tee 3/4in Slip X Slip X Slip
This is a regular 3/4"Slip x 3/4" Slip x 3/4" Slip pvc fitting available at most hardware stores -
Sku: 32467
Elbow, 45 Degree 2in
This elbow is used to join two 2" male PVC slip fittings or 2" PVC rigid or flex pipes together at a 45 degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
This PVC tee has three connections The two connections opposite each other are 2" slip connections, able to accept a 2" PVC pipe, or a 2" male PVC slip fitting The other connection, perpendicular to the other connections accepts a 1 1/2" PVC pipe or ...read more
-
Sku: 73456
Check Valve, Flow Control
This check valve is plumbed in line with the Bella Fontana and Amur water features in Hotsprings and Tiger River spas to keep the water flow through the fountain the same when the jet pumps are changed from low speed to high speed and vice versa
Showing 1–30 of 86 results