It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 90 results
-
Sku: 1044101-72228-AM-BYP
Tubing Kit, Del-Ozone-1/4in with Check valve
This 1/4" ID (3/8" OD) ozone-resistant tubing works with UO3 ozone generator It includes an attached 1/4" ozone-resistant check valve, clamps, mounting screws, and new flag terminals This assembly is approx five feet in length Note: There is a small ...read more -
Sku: 1044101-72228-BYP
Tubing Kit, Freshwater III Ozonator-1/4in Tygon/Kynar with Check valve
This 1/4" ID (3/8" OD) Kynar/Tygon ozone-resistant tubing kit comes standard with the Freshwater III Ozonators It is the replacement for all Freshwater 3 ozonators It includes an attached 1/4" ozone-resistant check valve This assembly is approx six feet ...read more -
Sku: 35233
Water Check Valve, 3/4 inch
This 3/4" water check valve is installed in the inlet side of the circulation pumps plumbing to prevent the backflow of water through the circulation pump once the jet pump is activated All water check valves have arrows stamped on the outside to indicate ...read more -
Air check valve for Hot Spring, Tiger River, and Hot Spot spa models This check valve is located in the equipment compartment under the bartop Its primary function is to prevent water from back flowing into the equipment compartment should a hydrotherapy ...read more
-
Sku: 38390
Check Valve, Air, with Ball 1/2in
It is used to prevent water from backing into the airlines when the jets are off It is at the back of the Moto-Massage housing and glued into a 90-degree elbow It is also on the jetstream jets -
Sku: 1044101
Check Valve (Ozone) Freshwater Ozone, 1/4in O.D.
Over time an Ozonator check valve will breakdown under the harsh conditions of ozone Our OEM check valves have a special diaphragm (Viton) that enables them to last longer than rubber Rubber diaphragms last about a month before the rubber becomes hard -
Sku: 36160
Precision Jet Tee
This tee is used to glue onto the rear of the Precision Jet Body and provides a 1/2" connection on either side of the tee This tee is not available at the local hardware store -
Sku: 37704
Diverter Body, 2-Port
This is a replacement valve body for 1994-2008 Hot Spring, Tiger River and all Limelight spa models with two-port diverter valves This valve body has 2" diameter ports and replaces the original black valve body -
Sku: 37297
6 Port Diverter Valve Body
This 6 port diverter valve body is used on the Hot Spring and Tiger River spa models that utilize a four-position valve -
Air control valve piston for all 1993-2003 Hot Spring and 1999-2003 Tiger River spa models Reference: 33837
-
Sku: 73916
Air Control Valve Piston
The piston turns by the valve lever to increase or decrease the airflow to the jets It is used on Hot Spring, Tiger River, Hot Spot, Solana, and Limelight spa models -
This air check valve is located in the equipment compartment, up high, under the bar top If a hydrotherapy jet should become obstructed (like when a guest sticks their finger in the jet), this item becomes critical in preventing water from back flowing into ...read more
-
Sku: 72701
Hartford Loop Assembly
This retrofit kit is used to replace the air check valve that was used in some Hot Spring spa models This kit replaces the obsolete 72342 Check your serial number in the parts finder above to be sure this part is for your spa -
Sku: 70425
Bypass Tee
This assembly is found on all Tiger River spas This 3/4" x 1/2" tee has 3/4" male barbed fittings on each end and a 1/2" barbed male fitting on the elbow It is located in front of the circulation pump between the check valve (35233) and the inlet of the ...read more -
This "Jet System" check valve is used on all Hot Spring models and all Tiger River spas This check valve engages when the diverter valve is changed to different positions For convenience, the inside diameter of this check valve is 1-1/2" and the outside ...read more
-
Sku: 75003
Air Control, Piston/Driver
ON BACKORDER WITH NO CURRENT ETA - The main air control valve component regulates the airflow to the jets when the lever is turned on all 1989-1993 Hot Spring spa models -
Sku: 70864
Check Valve, Safety Suction
This check valve's function is to "open" when someone puts their hand over the jet pumps suction fitting within the filter intake This check valve will "open" drawing air into it from the equipment compartment, thereby stopping suction of the jet pump This ...read more -
Barbed tee 1/4" on all three sides Used with 1/4" vinyl tubing and 1/4" clamps
-
Sku: 71981
Check Valve, with Spring, 1-1/2in
1-1/2" spring style check valve is commonly found between the jet pump and filter housing on Tiger River spas This check valve automatically closes when the Tiger River spas jet pump is turned off so the circulation pump (Silentflo 5000) can then draw water ...read more -
Sku: 31487
Tee, 1/2in X 1/2in Barb
Tee, Barbed, Black Poly, 1/2" x 1/2" x 1/2" -
Sku: 31309
Valve Body, Air Control
Air control valve body used on all Hot Spring spas from 1989-mid 1993 This part is found under the bar top on the backside of the spa shell It is sealed to the bottom of the bar top using an o-ring so that water splashed on it does not leak into the ...read more -
Sku: 30626
Tee, 1/2in Slip X Slip X Slip
This PVC tee will accept 1/2" male rigid or flexible PVC pipe or male PVC fittings 1/2" schedule 40 thick-walled clear vinyl PVC can also be glued directly to this fitting PVC primer and cement should be used on this fitting Failing to use primer ...read more -
Reducer Bushing, 3/4" Spig x 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 3/4" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 30502
Diverter Valve Body, 1-1/2in
Replacement valve body for Hot Spring spa models manufactured prior to 1994 This gray valve body has 1-1/2" diameter ports This valve body typically sits above the jet pump for diverting water from one area of the spa to the other Use with Valve Insert ...read more -
Sku: 34458
Red Tee 2in X 1-1/2in X 1-1/2in
PVC tee, 2" X 1-1/2" X 1-1/2" slip -
Sku: 72185
Diverter valve Tee
Tee for 2 position diverter valve -
Sku: 32465
Tee 2in
This tee allows three 2" male PVC slip connections, or 2" PVC pipe (rigid or flexible) to be joined together, one of which is perpendicular to the other two connections PVC primer and glue should be used to adhere to the male connections tog the fitting -
Sku: 33838
Valve Body, Air Control
This is part of the air control valves used on Hotspring and Tiger River spas from 1999 to 2003 It is where the moving portion of the valve resides and where the plumbing connects to the valve, as well as provides a way to mount the valve to the shell of ...read more -
Sku: 30681
Bushing, 1-1/2in X 1in Sp X Slip
This bushing is used to adapt a 1" male PVC slip fitting to fit in a 1 1/2" female slip fitting, or to allow a 1 1/2" female slip fitting to accept a 1" male slip fitting -
Sku: 34751
Tee 3/4in Slip X Slip X Slip
This is a regular 3/4"Slip x 3/4" Slip x 3/4" Slip pvc fitting available at most hardware stores
Showing 1–30 of 90 results