I have always found the Backyard Plus sales representatives to be knowledgeable and helpful. The prices are great. This is my go to place for my hot tub.On 05/29/2024 by D. F. (verified customer)
Find all the plumbing parts you need here. Flexi PVC tubing, Vinyl Tubing, Elbows, Tees, Diverter Valves, Levers & Bezels, Check-Valves, Couplers, and more.
Showing 1–30 of 43 results
-
Sku: 30237-x2-BYP
Compression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 32267-1
Drain Plug, Wavemaster
This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline For spas with a bleedline, the 32267 is used in place of this fitting This drain plug can be ...read more -
Sku: 301488
Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401
Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit
-
Sku: 11080
449-020 2in Plug
This is a 2" PVC plug It can be used to plug any 2" female PVC fitting and should be installed using PVC primer and cement You can get PVC cement at your local hardware store -
Reducer Bushing, 3/4" Spig x 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 3/4" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 30681
Bushing, 1-1/2in X 1in Sp X Slip
This bushing is used to adapt a 1" male PVC slip fitting to fit in a 1 1/2" female slip fitting, or to allow a 1 1/2" female slip fitting to accept a 1" male slip fitting -
Sku: 30697
Plug, 3/4in Spig
Plug, PVC, 3/4" Spig This plug is made out of PVC and fits in a female PVC slip fitting It can be used to plug an extra port on a manifold or tee that is not needed Or cap off a piece of plumbing that is no longer used -
Reducing Bushing, 1"Spig X 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 70906
Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Sku: 31420
Bushing, 1-1/2in X 3/4in Slip X Slip
This bushing accepts a 3/4" male PVC slip fitting or 3/4" PVC pipe, rigid or flexible, and will connect to a 1 1/2" female PVC slip fitting -
Sku: 30680
Bushing, 1-1/2in X 3/4in Sp X Slip
This bushing accepts a 3/4" male PVC slip fitting and will fit into a 1 1/2" female PVC slip fitting PVC primer and cement should be used to adhere this fitting -
Reducer Bushing, 1" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement
-
Sku: 30685
Bushing, 2in X 1in Spig X Slip
This bushing accepts a 1" male PVC slip fitting and will fit into a 2" female PVC slip fitting PVC primer and cement should be used to adhere to this fitting -
Sku: 37681
Red Bushing, 2in X 3/4in (437-248)
Reducer Bushing, 2" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 2" female slip fitting The connection should be made using PVC primer and cement -
Sku: 74135
Bleedline Bushing, Hot Spring
Bleedline Bushing for 2001 Hot Spring Landmark Dream Jet Massage Plumbing System Fits between the spa shell and the bleedline fitting, part number 30598 The bleedline fitting supplies a small stream of water behind the pillow to prevent water from ...read more -
Sku: 73808
Ozone Restrictor, Freshwater 3
Flow restrictor for the Freshwater III ozone unit used to reduce the ozone order and/or to eliminate any "burping" noise emanating from the spa Simply remove the air filter from your Freshwater unit and attach to this flow restrictor as shown in the picture ...read more -
Sku: 31485
Bushing, 1-1/4in X 1in
This bushing accepts a 1" pipe or male PVC fitting and will fit into a 1 1/4" female PVC fitting PVC primer and cement should be used to adhere the fittings together -
Sku: 30699
Plug, 1-1/2in Spig
This PVC fitting is used to plug 1 1/2" female PVC slip fittings It should be attached using PVC primer and cement, which is available at your local hardware store It is made out of white PVC plastic -
Sku: 30698
Plug, 1in Spig
This is a 1" PVC plug It is used to plug a 1" female PVC fitting and should be attached using PVC cement and PVC primer This will usually be used when a fitting has multiple openings, and not all of the openings are being used -
Sku: 30696
Plug 1/2in Spig
Plug, PVC, 1/2" Spig -
This bushing accepts a 1/2" male pipe thread fitting and will connect to a 2" female PVC slip fitting PVC primer and cement should be used for the slip fitting side of this bushing Plumbers tape should be used on the 1/2" male pipe thread before it is ...read more
-
Reducer Bushing 1-1/2" Spig x 3/4 female iron pipe thread This bushing allows a 3/4" male pipe threaded fitting to be adapted to fit in a 1 1/2" female slip fitting The connection should be made using PVC primer and cement on the slip portion of the ...read more
-
This bushing adapts a 1/2" male PVC slip fitting to a 1/4" spig fitting PVC primer and cement should be used on the slip fitting
-
This bushing accepts a 1/2" male PVC slip fitting and will fit into a 2" female PVC slip fitting PVC primer and cement should be used to adhere this fitting
-
Reducer Bushing, 1-1/2" Spig x 1-1/4" Slip This bushing reduces a 1 1/2" female slip fitting down to a 1 1/4" female slip fitting PVC primer and cement should be used to glue the bushing in place
-
This PVC fitting converts a 1 1/2" female slip fitting down to a 1/2" female slip fitting PVC primer and cement should be used to make the connections
-
Reducer Bushing, 1-1/4" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1 1/4" female slip fitting The connection should be made using PVC primer and cement
Showing 1–30 of 43 results