Great service, great price. When it appeared the shipment might be a day or so late, there was great communication. We will definitely be back as a customer.On 07/03/2024 by G. L. (verified customer)
Brand: Hot Spring | Plumbing: Air Manifold, Barbed Adapter, Barbed Fitting, Cross, Inlet, Plug, Split Nut, Union
Showing 1–30 of 44 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more -
Sku: 70382Coupling, Barbed, 1/4in x 1/4in
Barbed coupling used to splice together 1/4" vinyl tubing -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit -
This coupling is most often found on the discharge side of the Laing 303 and Calvert (Cal-200) circulating pumps The 3/4" x 3/4" x 1/4" bleed line fitting has a 1/4" nipple (30598) for the 1/4" vinyl tubing that's coming from the front of the jet pump to ...read more -
Sku: 70383Coupling, Barbed, 1/2in x 1/2in
Barbed coupling used to splice together 1/2" vinyl tubing -
This coupling is made from an ozone resistant plastic called Kynar It is connected to the side of the newest style of Freshwater III Ozonator, 72602 The ozone tubing connects onto this barbed fitting If your barbed fitting breaks off, this factory ...read more -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system or jets in a Hot Spring & Tiger River spa It simply glues into a 1/2" PVC coupling or elbow with regular PVC cement -
Sku: 010009Barbed adapter 1 in x 3/8 Spigot
Barbed adapter 1 inch by 3/8 inch 425-5010 BARB ADAP 1IN(1)3/8IN -
Sku: 72072-1.5Split Nut for 1.5in Compression Fittings
This 1-1/2" split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age, and over-tightening The two halves of this fitting are held together by two screws -
Sku: 397055 Port Air Manifold, 1in x 3/8in
PVC air manifold, 1" X 3/8", 5-Port -
Barbed adapter which is 1/2" male threads on one end and 1/2" barbed on the other -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system of Hot Spring spa models -
Sku: 30586Barbed Adapter, 1/4in X 5/16in
This barbed adapter is used in various places but primarily in the Moto-Massage niche for the small silicone Moto-Massage Jet air tube to slip onto on pre-1997 Hot Spring spa models -
Sku: 39707Air Manifold, PVC 1inx3/8in, 4 Port
PVC air manifold, 1" X 3/8", 4-Port -
Sku: 36977Air Manifold, 4 Port, 3/8in Barbs
This four-port manifold is typically used to feed air to the Precision Jets in a Hot Spring and Tiger River spa This 4 port manifold comes with one end capped off and the other end is 1" slip Depending on the current configuration of yours, the 1" may need ...read more -
Sku: 304654Coupling, Barbed, 3/4in x 3/4in
This is a barbed coupling used to splice together 3/4" vinyl tubing used in Hot Spring & Tiger River, Limelight, Hot Spot and Solana spas This fitting would normally be used to repair a broken line Replaces item 70384 -
Barbed adapter which is 3/4" male threads on one end and 1/2" barbed on the other -
Sku: 75001Pump Inlet Assembly, Grandee
The three pieces of this pump inlet assembly come pre-assembled and include the check valve This assembly was used on the jet pump on the 1989-1990 Hot Spring Grandee (G 191001 to G 109999) -
Sku: 75010Inlet Assembly with Check Valve
The four pieces of this pump inlet assembly come pre-assembled and include the check valve This assembly was used on the jet pump on the 1989 Hot Spring Jetsetter, Prodigy, and Sovereign Also used on the 1991-1992 Grandee -
PVC air manifold, 1" Barb Adap, 3/8", 2-Port -
Sku: 362958-Port Air Manifold
8-port PVC air manifold -
Sku: 38674Cross, 2in Slip
Cross, PVC, 2" slip x slip x slip x slip -
Sku: 7203210 Port Air Manifold
Air manifold: 10" long with 1/2" barbed in and 3/8" barbed out x 10 -
Sku: 397037 Port Air Manifold, 1in X 1in X 3/8in
This 6 port air manifold is used in various spa models It's a one-inch slip with six 3/8" barbed nipples to connect the 3/8" tubing For the 1/2" version see part 38397 -
This 6 port air manifold is used in various spa models It's half-inch slip with six 3/8" barbed nipples to connect the 3/8" tubing For the 1" version see part 39703 -
Sku: 30699Plug, 1-1/2in Spig
This PVC fitting is used to plug 1 1/2" female PVC slip fittings It should be attached using PVC primer and cement, which is available at your local hardware store It is made out of white PVC plastic
Showing 1–30 of 44 results