I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Plumbing: Adapter, Air Filter, Flange, Inlet, Jet, Split Nut, Union
Showing 1–30 of 46 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more -
Sku: 31417Adapter, 3/4in Barbed X 3/4in Slip
This barbed fitting is primarily used to connect 3/4" vinyl tubing to various places within the circulating/heating system of Hot Spring & Tiger River from 1990 forward This PVC fitting is often found glued into a 90-degree elbow rising from the floor of ...read more -
Sku: 34504Adapter, 3/4in Sp X 1/4in Sp
This adapter glues into a 3/4" female PVC slip fitting using PVC primer and cement and accepts a 1/4" vinyl hose that can be secured using PVC cement as well or a hose clamp -
Sku: 30703Adapter, 3/4in X 3/4in Mht X Slip
This PVC fitting glues on to a 3/4" male PVC rigid or flexible pipe and allows a 3/4" female pipe thread to connect to it On Hotsprings and Tiger River spas, it's used as part of the drain system, to allow a garden hose to be connected and water to be ...read more -
This coupling is made from an ozone resistant plastic called Kynar It is connected to the side of the newest style of Freshwater III Ozonator, 72602 The ozone tubing connects onto this barbed fitting If your barbed fitting breaks off, this factory ...read more -
Sku: 72072-1.5Split Nut for 1.5in Compression Fittings
This 1-1/2" split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age, and over-tightening The two halves of this fitting are held together by two screws -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
This white flange attaches to the front of the drain valve (slide valve style) and attaches with four screws -
Sku: 31556Adapter, 1/4in X 1/4in Spig X Slip
Adapter, Barb x Socket, 1/4" x 1/4" -
Sku: 31348Adapter, 1-1/2in Mipt
This male adapter screws into a 1-1/2" jet pump volute in order for a 1-1/2" compression coupling (pump union) to screw onto the adapter -
PVC elbow that allows a 3/4" barbed fitting and a 3/4" threaded fitting to be connected together Both fittings are male, and the barbed fitting should be secured using hose clamps, and the threaded fitting should be wrapped in Teflon tape before installing ...read more -
Sku: 39438Adapter, Ell 1/2in Hose X 1/4in Mpt
Adapter, barbed ell, PVC, 1/2" hose x 1/4", male pipe thread -
Sku: 70906Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Used on the 1995-1997 Hot Spot spas this fitting provided a flange for the cartridge-style heater element to seal against and a "dry-well" for the thermistor probe to slide into -
Sku: 70245Flange, Rear-Slide Drain-Slip
Flange, rear-slide, drain-slip Hot Spring models 1990 - 1992 slide valve -
Sku: 30690Adapter, 3/8 X 1/2 Mipt X Fipt
This adapter Used with the 30118 thermostat cord grip -
Sku: 30702Adapter, 3/4in X 1/2in Mht X Slip
This PVC fitting accepts a 1/2" male slip fitting or 1/2" PVC pipe and should be attached using PVC primer and cement The other end is a 3/4" male pipe thread and can be used to connect fittings such as a garden hose This part is used commonly in the ...read more -
Sku: 75001Pump Inlet Assembly, Grandee
The three pieces of this pump inlet assembly come pre-assembled and include the check valve This assembly was used on the jet pump on the 1989-1990 Hot Spring Grandee (G 191001 to G 109999) -
Sku: 75010Inlet Assembly with Check Valve
The four pieces of this pump inlet assembly come pre-assembled and include the check valve This assembly was used on the jet pump on the 1989 Hot Spring Jetsetter, Prodigy, and Sovereign Also used on the 1991-1992 Grandee -
Sku: 31486Adapter, 3/4in Slip
Adapter, Barb x Socket, 3/4" x 3/4" -
2" X 1-1/2" male adapter commonly used on the suction side of pumps -
This PVC fitting has a female PVC slip fitting and a male pipe thread fitting So it can accept a 1" PVC pipe or male PVC slip fitting and can screw into a 3/4" female pipe threaded fitting -
This PVC fitting accepts a 1 1/2" male PVC fitting or 1/2" PVC rigid or flexible pipe and has a 1 1/2" male pipe thread fitting on the other end It should be attached using PVC primer and cement -
Sku: 30671Adapter, 1/2in Mipt x slip
This PVC fitting accepts a 1/2" male PVC fitting or 1/2" PVC rigid or flexible pipe and has a 1/2" male pipe thread fitting on the other end It should be attached using PVC primer and cement -
This coupling is used to connect a 1/2" male PVC slip fitting a 1/2" PVC female pipe threaded connection together PVC primer and cement should be used to adhere to this fitting -
Sku: 30549Union, 1-1/2in Slip x Threaded
Union, 1-1/2in slip x threaded
Showing 1–30 of 46 results