I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Showing 1–30 of 92 results
-
Sku: 30598
Bleedline Nipple, 1/4in, Hot Spring
This nipple is glued into various PVC fittings in various places on Hot Spring, Tiger River, Limelight, Hot Spot and Solana spa models Simply drill out the broken 1/4" barbed fitting with a 19/64" drill bit (only this size drill bit) Then glue this ...read more -
Sku: 32267-1
Drain Plug, Wavemaster
This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline For spas with a bleedline, the 32267 is used in place of this fitting This drain plug can be ...read more -
Sku: 36160
Precision Jet Tee
This tee is used to glue onto the rear of the Precision Jet Body and provides a 1/2" connection on either side of the tee This tee is not available at the local hardware store -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit
-
Sku: 31417
Adapter, 3/4in Barbed X 3/4in Slip
This barbed fitting is primarily used to connect 3/4" vinyl tubing to various places within the circulating/heating system of Hot Spring & Tiger River from 1990 forward This PVC fitting is often found glued into a 90-degree elbow rising from the floor of ...read more -
Sku: 34504
Adapter, 3/4in Sp X 1/4in Sp
This adapter glues into a 3/4" female PVC slip fitting using PVC primer and cement and accepts a 1/4" vinyl hose that can be secured using PVC cement as well or a hose clamp -
Sku: 11080
449-020 2in Plug
This is a 2" PVC plug It can be used to plug any 2" female PVC fitting and should be installed using PVC primer and cement You can get PVC cement at your local hardware store -
Sku: 77427
Bleedline Fitting, Circulation Pump
Circulation Pump Bleedline Fitting This special Tee fitting includes 2 X 3/4" barbed fittings, as well as a 1/4" connection No PVC Glue needed and no assembly required like the 72727-BYP (Elbow, 3/4in X 3/4in Barbed with 1/4in Barbed Nipple) -
Sku: 70425
Bypass Tee
This assembly is found on all Tiger River spas This 3/4" x 1/2" tee has 3/4" male barbed fittings on each end and a 1/2" barbed male fitting on the elbow It is located in front of the circulation pump between the check valve (35233) and the inlet of the ...read more -
Sku: 30703
Adapter, 3/4in X 3/4in Mht X Slip
This PVC fitting glues on to a 3/4" male PVC rigid or flexible pipe and allows a 3/4" female pipe thread to connect to it On Hotsprings and Tiger River spas, it's used as part of the drain system, to allow a garden hose to be connected and water to be ...read more -
Barbed tee 1/4" on all three sides Used with 1/4" vinyl tubing and 1/4" clamps
-
Sku: 31487
Tee, 1/2in X 1/2in Barb
Tee, Barbed, Black Poly, 1/2" x 1/2" x 1/2" -
Sku: 30626
Tee, 1/2in Slip X Slip X Slip
This PVC tee will accept 1/2" male rigid or flexible PVC pipe or male PVC fittings 1/2" schedule 40 thick-walled clear vinyl PVC can also be glued directly to this fitting PVC primer and cement should be used on this fitting Failing to use primer ...read more -
Sku: 34458
Red Tee 2in X 1-1/2in X 1-1/2in
PVC tee, 2" X 1-1/2" X 1-1/2" slip -
Sku: 32465
Tee 2in
This tee allows three 2" male PVC slip connections, or 2" PVC pipe (rigid or flexible) to be joined together, one of which is perpendicular to the other two connections PVC primer and glue should be used to adhere to the male connections tog the fitting -
Sku: 34751
Tee 3/4in Slip X Slip X Slip
This is a regular 3/4"Slip x 3/4" Slip x 3/4" Slip pvc fitting available at most hardware stores -
Sku: 32467
Elbow, 45 Degree 2in
This elbow is used to join two 2" male PVC slip fittings or 2" PVC rigid or flex pipes together at a 45 degree angle PVC primer and cement should be used to secure this fitting to the fittings it is joining together -
Sku: 31556
Adapter, 1/4in X 1/4in Spig X Slip
Adapter, Barb x Socket, 1/4" x 1/4" -
This PVC tee has three connections The two connections opposite each other are 2" slip connections, able to accept a 2" PVC pipe, or a 2" male PVC slip fitting The other connection, perpendicular to the other connections accepts a 1 1/2" PVC pipe or ...read more
-
Sku: 31348
Adapter, 1-1/2in Mipt
This male adapter screws into a 1-1/2" jet pump volute in order for a 1-1/2" compression coupling (pump union) to screw onto the adapter -
Sku: 30697
Plug, 3/4in Spig
Plug, PVC, 3/4" Spig This plug is made out of PVC and fits in a female PVC slip fitting It can be used to plug an extra port on a manifold or tee that is not needed Or cap off a piece of plumbing that is no longer used -
Sku: 30627
Tee, 1in Slip X Slip X Slip
This Tee accepts three 1 inch PVC pipe connections or male PVC fittings All connections should be made using both PVC primer and PVC cement The connections are oriented in a T style layout
Showing 1–30 of 92 results