I would like to express how excellent this company is. I inherited a house with a 2007 Hotspring Aria hot tub. The spa hasn’t been operated in years and when I turned it on, it ran for about 10 minutes and died. I mean dead died. I knew absolutely nothing about hot tubs but with the excellent diagnosis videos, installation videos and superior phone support, I was able to replace the main control board, heater relay board, heater, circulation pump, the ozonator and all associated tubing. This took 4 1/2 hours over two days (I had to watch videos) but the spa runs like new! I had one question regarding the jumper voltage 18 or 12. I spoke with a technician and he was able to answer my question as well as helping me double check the voltages for the components on the relay board. I am handy with electronics and electricity and am comfortable working with 230 volts. Shipping was fast and as expected. I highly recommend BackYardPlus.On 06/28/2024 by F. R. (verified customer)
Plumbing: Adapter, Flange, Handles Knobs Levers Bezels, Plug, Snap Ring
Showing 1–30 of 45 results
-
Sku: 32267-1Drain Plug, Wavemaster
This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline For spas with a bleedline, the 32267 is used in place of this fitting This drain plug can be ...read more -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit -
Sku: 31417Adapter, 3/4in Barbed X 3/4in Slip
This barbed fitting is primarily used to connect 3/4" vinyl tubing to various places within the circulating/heating system of Hot Spring & Tiger River from 1990 forward This PVC fitting is often found glued into a 90-degree elbow rising from the floor of ...read more -
Sku: 34504Adapter, 3/4in Sp X 1/4in Sp
This adapter glues into a 3/4" female PVC slip fitting using PVC primer and cement and accepts a 1/4" vinyl hose that can be secured using PVC cement as well or a hose clamp -
Sku: 11080449-020 2in Plug
This is a 2" PVC plug It can be used to plug any 2" female PVC fitting and should be installed using PVC primer and cement You can get PVC cement at your local hardware store -
Sku: 30703Adapter, 3/4in X 3/4in Mht X Slip
This PVC fitting glues on to a 3/4" male PVC rigid or flexible pipe and allows a 3/4" female pipe thread to connect to it On Hotsprings and Tiger River spas, it's used as part of the drain system, to allow a garden hose to be connected and water to be ...read more -
This coupling is made from an ozone resistant plastic called Kynar It is connected to the side of the newest style of Freshwater III Ozonator, 72602 The ozone tubing connects onto this barbed fitting If your barbed fitting breaks off, this factory ...read more -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
This white flange attaches to the front of the drain valve (slide valve style) and attaches with four screws -
Sku: 31556Adapter, 1/4in X 1/4in Spig X Slip
Adapter, Barb x Socket, 1/4" x 1/4" -
Sku: 31348Adapter, 1-1/2in Mipt
This male adapter screws into a 1-1/2" jet pump volute in order for a 1-1/2" compression coupling (pump union) to screw onto the adapter -
Sku: 30697Plug, 3/4in Spig
Plug, PVC, 3/4" Spig This plug is made out of PVC and fits in a female PVC slip fitting It can be used to plug an extra port on a manifold or tee that is not needed Or cap off a piece of plumbing that is no longer used -
PVC elbow that allows a 3/4" barbed fitting and a 3/4" threaded fitting to be connected together Both fittings are male, and the barbed fitting should be secured using hose clamps, and the threaded fitting should be wrapped in Teflon tape before installing ...read more -
Sku: 39438Adapter, Ell 1/2in Hose X 1/4in Mpt
Adapter, barbed ell, PVC, 1/2" hose x 1/4", male pipe thread -
Used on the 1995-1997 Hot Spot spas this fitting provided a flange for the cartridge-style heater element to seal against and a "dry-well" for the thermistor probe to slide into -
Sku: 70245Flange, Rear-Slide Drain-Slip
Flange, rear-slide, drain-slip Hot Spring models 1990 - 1992 slide valve -
Sku: 30690Adapter, 3/8 X 1/2 Mipt X Fipt
This adapter Used with the 30118 thermostat cord grip -
Sku: 30702Adapter, 3/4in X 1/2in Mht X Slip
This PVC fitting accepts a 1/2" male slip fitting or 1/2" PVC pipe and should be attached using PVC primer and cement The other end is a 3/4" male pipe thread and can be used to connect fittings such as a garden hose This part is used commonly in the ...read more -
Sku: 70825-BYPSnap Ring Pliers Tool, Smart Jet Diverter Valve
These snap ring ("c"-ring) pliers can be used to remove the snap ring on Smart Jet diverter valves (71494, 71495, 73768, 73769) found in most hot tubs Made of carbon steel and vinyl grip handles and comes with interchangable straight, 45 degree and 90 degree ...read more -
Sku: 31486Adapter, 3/4in Slip
Adapter, Barb x Socket, 3/4" x 3/4" -
Sku: 30699Plug, 1-1/2in Spig
This PVC fitting is used to plug 1 1/2" female PVC slip fittings It should be attached using PVC primer and cement, which is available at your local hardware store It is made out of white PVC plastic -
Sku: 30698Plug, 1in Spig
This is a 1" PVC plug It is used to plug a 1" female PVC fitting and should be attached using PVC cement and PVC primer This will usually be used when a fitting has multiple openings, and not all of the openings are being used -
Sku: 30696Plug 1/2in Spig
Plug, PVC, 1/2" Spig -
2" X 1-1/2" male adapter commonly used on the suction side of pumps -
This PVC fitting has a female PVC slip fitting and a male pipe thread fitting So it can accept a 1" PVC pipe or male PVC slip fitting and can screw into a 3/4" female pipe threaded fitting -
This PVC fitting accepts a 1 1/2" male PVC fitting or 1/2" PVC rigid or flexible pipe and has a 1 1/2" male pipe thread fitting on the other end It should be attached using PVC primer and cement -
Sku: 30671Adapter, 1/2in Mipt x slip
This PVC fitting accepts a 1/2" male PVC fitting or 1/2" PVC rigid or flexible pipe and has a 1/2" male pipe thread fitting on the other end It should be attached using PVC primer and cement -
This coupling is used to connect a 1/2" male PVC slip fitting a 1/2" PVC female pipe threaded connection together PVC primer and cement should be used to adhere to this fitting -
Sku: 017069Plug, Hole Plug, Heyco #2753
This black hole plug is used on most Hot Spot spas to plug unused holes provided for electrical conduit Usually, there are two holes predrilled, so that the conduit can enter the equipment compartment of the spa from either side This plug is used to ...read more -
Sku: 35749Bleedline Coupling Assembly, Highlife
Bleedline coupling assembly, Highlife See also, 72726
Showing 1–30 of 45 results