It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Plumbing: Adapter, On Off Valve, Reducer, Ring, Union
Showing 1–30 of 55 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: 31417Adapter, 3/4in Barbed X 3/4in Slip
This barbed fitting is primarily used to connect 3/4" vinyl tubing to various places within the circulating/heating system of Hot Spring & Tiger River from 1990 forward This PVC fitting is often found glued into a 90-degree elbow rising from the floor of ...read more -
Sku: 73920Water Feature On-Off Valve Assembly
This on-off valve assembly is found on Hot Spot and Limelight spa models from 2006 through 2014 It is used to turn on and off the bar top Amur water feature that runs off one of the jet pumps in the spa This valve turns 270 degrees, for 2014 tubs, please ...read more -
Sku: 34504Adapter, 3/4in Sp X 1/4in Sp
This adapter glues into a 3/4" female PVC slip fitting using PVC primer and cement and accepts a 1/4" vinyl hose that can be secured using PVC cement as well or a hose clamp -
Sku: 30703Adapter, 3/4in X 3/4in Mht X Slip
This PVC fitting glues on to a 3/4" male PVC rigid or flexible pipe and allows a 3/4" female pipe thread to connect to it On Hotsprings and Tiger River spas, it's used as part of the drain system, to allow a garden hose to be connected and water to be ...read more -
This coupling is made from an ozone resistant plastic called Kynar It is connected to the side of the newest style of Freshwater III Ozonator, 72602 The ozone tubing connects onto this barbed fitting If your barbed fitting breaks off, this factory ...read more -
Reducer Bushing, 3/4" Spig x 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 3/4" female slip fitting The connection should be made using PVC primer and cement -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
Sku: 31556Adapter, 1/4in X 1/4in Spig X Slip
Adapter, Barb x Socket, 1/4" x 1/4" -
Sku: 31348Adapter, 1-1/2in Mipt
This male adapter screws into a 1-1/2" jet pump volute in order for a 1-1/2" compression coupling (pump union) to screw onto the adapter -
Sku: 31288Reducer, 2in X 1-1/2in Spig X Slip
Reducer Bushing, 2" Spig x 1-1/2" Slip This bushing allows for a 1 1/2" male slip fitting or PVC pipe, rigid or flexible, to connect to a 2" female slip fitting The connection should be made using PVC primer and cement -
Reducing Bushing, 1"Spig X 1/2" Slip This bushing allows a 1/2" male slip fitting or 1/2" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement -
PVC elbow that allows a 3/4" barbed fitting and a 3/4" threaded fitting to be connected together Both fittings are male, and the barbed fitting should be secured using hose clamps, and the threaded fitting should be wrapped in Teflon tape before installing ...read more -
Sku: 39438Adapter, Ell 1/2in Hose X 1/4in Mpt
Adapter, barbed ell, PVC, 1/2" hose x 1/4", male pipe thread -
Sku: 70906Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Sku: 30690Adapter, 3/8 X 1/2 Mipt X Fipt
This adapter Used with the 30118 thermostat cord grip -
Reducer Bushing, 1" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1" female slip fitting The connection should be made using PVC primer and cement -
Sku: 30702Adapter, 3/4in X 1/2in Mht X Slip
This PVC fitting accepts a 1/2" male slip fitting or 1/2" PVC pipe and should be attached using PVC primer and cement The other end is a 3/4" male pipe thread and can be used to connect fittings such as a garden hose This part is used commonly in the ...read more -
Sku: 30667Coupling, Reducer 1in X 3/4in Sxs
This adapter is used to join a 3/4" PVC male fitting and a 1" PVC male fitting together PVC primer and cement should be used to adhere the fittings -
Sku: 37681Red Bushing, 2in X 3/4in (437-248)
Reducer Bushing, 2" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 2" female slip fitting The connection should be made using PVC primer and cement -
Sku: 31486Adapter, 3/4in Slip
Adapter, Barb x Socket, 3/4" x 3/4" -
Reducer Bushing 1-1/2" Spig x 3/4 female iron pipe thread This bushing allows a 3/4" male pipe threaded fitting to be adapted to fit in a 1 1/2" female slip fitting The connection should be made using PVC primer and cement on the slip portion of the ...read more -
Reducer Bushing, 1-1/2" Spig x 1-1/4" Slip This bushing reduces a 1 1/2" female slip fitting down to a 1 1/4" female slip fitting PVC primer and cement should be used to glue the bushing in place -
Reducer Bushing, 1-1/4" Spig x 3/4" Slip This bushing allows a 3/4" male slip fitting or 3/4" PVC pipe, rigid or flexible, to be adapted to fit in a 1 1/4" female slip fitting The connection should be made using PVC primer and cement -
2" X 1-1/2" male adapter commonly used on the suction side of pumps -
This PVC fitting has a female PVC slip fitting and a male pipe thread fitting So it can accept a 1" PVC pipe or male PVC slip fitting and can screw into a 3/4" female pipe threaded fitting -
This PVC fitting accepts a 1 1/2" male PVC fitting or 1/2" PVC rigid or flexible pipe and has a 1 1/2" male pipe thread fitting on the other end It should be attached using PVC primer and cement
Showing 1–30 of 55 results