It was very easy to select the corret parts for my "serial Number". All parts were correct and operated as required.On 06/20/2024 by M. R. (verified customer)
Plumbing: Air Manifold, Barbed Fitting, Gasket, Union, Water Manifold
Showing 1–30 of 60 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: 70382Coupling, Barbed, 1/4in x 1/4in
Barbed coupling used to splice together 1/4" vinyl tubing -
This coupling is most often found on the discharge side of the Laing 303 and Calvert (Cal-200) circulating pumps The 3/4" x 3/4" x 1/4" bleed line fitting has a 1/4" nipple (30598) for the 1/4" vinyl tubing that's coming from the front of the jet pump to ...read more -
Sku: 79140Bleedline Kit, Hot Spot Relay and Rhythm
This bleedline kit should be used with your jet pump if you're experiencing air lock issues -
Sku: 70383Coupling, Barbed, 1/2in x 1/2in
Barbed coupling used to splice together 1/2" vinyl tubing -
This coupling is made from an ozone resistant plastic called Kynar It is connected to the side of the newest style of Freshwater III Ozonator, 72602 The ozone tubing connects onto this barbed fitting If your barbed fitting breaks off, this factory ...read more -
Sku: 70189Drain Valve Gasket, Slide Valve Style
This black 1-1/2" black gasket is found on both sides of the slide handle body 70247 (obsolete) -
Sku: 304653Coupler, Barbed, 3/8in x 3/8in
3/8" barbed coupling used to splice in 3/8" vinyl tubing (70317) Old item number 72582 -
Sku: 397055 Port Air Manifold, 1in x 3/8in
PVC air manifold, 1" X 3/8", 5-Port -
Sku: 38429Water Manifold,1in X 1/2in 4-Port
Water Manifold, 1" x 1/2" 4-port -
Sku: 34338Manifold, Flow Cone
Manifold, flow cone -
Sku: 39707Air Manifold, PVC 1inx3/8in, 4 Port
PVC air manifold, 1" X 3/8", 4-Port -
Sku: 36977Air Manifold, 4 Port, 3/8in Barbs
This four-port manifold is typically used to feed air to the Precision Jets in a Hot Spring and Tiger River spa This 4 port manifold comes with one end capped off and the other end is 1" slip Depending on the current configuration of yours, the 1" may need ...read more -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
Sku: 397046-3/4 Port Water Manifold, 2in Slip PVC
PVC water manifold, 2" Slip x 6 Port 3/4" -
Sku: 33370Gasket, Silicone 2-3/8in Inside Diameter
Silicone gasket, 2 3/8in -
Sku: 304654Coupling, Barbed, 3/4in x 3/4in
This is a barbed coupling used to splice together 3/4" vinyl tubing used in Hot Spring & Tiger River, Limelight, Hot Spot and Solana spas This fitting would normally be used to repair a broken line Replaces item 70384 -
Sku: 39702Manifold, Water, 2in X 1/2in, 6-Port
PVC water manifold, 2" X 1/2", 6-Port -
Sku: 70906Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Sku: 300042Manifold, 2 Port, 3/4in X 1/2in X 1/2in
Wye manifold with 3/4" slip inlet to two 1/2" slip outlets Used on Hot Spring, Tiger River, Hot Spot & Solana spa models PVC cement and primer should be used to make the connections to this manifold -
Sku: 301235Manifold 1.5in X X 1.5in SP X (4)
Manifold, 1 5inch slip by 1 5 SP x 4 -
PVC water manifold, 1-1/2" X 1/2", 6-Port -
Sku: 75044Barbed Fitting, 3/4in Elbow Repair
This barbed fitting is 1/2" slip on one end and 3/4" barbed on the other It is used to repair a broken 1/2" elbow that comes out of the floor of the Hot Spring equipment compartment and nineties into the circulation pump This fitting will glue into the ...read more -
Sku: 10566018 Port Manifold, 2-1/2in x 3/4in
This is a manifold with 2-1/2" slip inlet to eight 3/4" slip outlets It can be used with rigid or flexible PVC piping or male PVC slip fittings PVC primer and cement should be used to adhere to the connections -
PVC air manifold, 1" Barb Adap, 3/8", 2-Port -
Sku: 362958-Port Air Manifold
8-port PVC air manifold -
Sku: 010020Four Barbed Water Manifold
Four barbed water manifold (MANIFOLD 4 BARB 1INX3/8IN) for Hot Spring, Hot Spot, and Limelight models
Showing 1–30 of 60 results