The team at Backyardplus.com are the best for anything Hot Springs. Super friendly and knowledgeable.On 06/05/2024 by S. O. (verified customer)
Plumbing: Barbed Adapter, Snap Ring, Union, Wallfitting
Showing 1–30 of 33 results
-
Sku: 30237-x2-BYPCompression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 301488Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: 30490Wallfitting, Rear
This fitting is used on many different Hot Spring spa models in various places including the grill style filter compartment as part of the filter assembly Also used in the filter compartment of all 1992-1996 Tiger River spa models -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system or jets in a Hot Spring & Tiger River spa It simply glues into a 1/2" PVC coupling or elbow with regular PVC cement -
Sku: 010009Barbed adapter 1 in x 3/8 Spigot
Barbed adapter 1 inch by 3/8 inch 425-5010 BARB ADAP 1IN(1)3/8IN -
This threaded wall fitting is located in the bottom of the filter compartment on all 1997-2010 Tiger River Bengal, Caspian, Sumatran & Siberian spa models This is where the filter standpipe screws into -
Barbed adapter which is 1/2" male threads on one end and 1/2" barbed on the other -
This barbed fitting is primarily used to connect 1/2" vinyl tubing to various places within the circulating/heating system of Hot Spring spa models -
Sku: 30586Barbed Adapter, 1/4in X 5/16in
This barbed adapter is used in various places but primarily in the Moto-Massage niche for the small silicone Moto-Massage Jet air tube to slip onto on pre-1997 Hot Spring spa models -
Sku: 71128Wallfitting, Drain Drilled
Wall fitting, rear drain, 1/2" drilled, Hot Spring Rear wall fitting located in the footwell of the spa Front wall fitting part 30488 -
Sku: 70846Connector 3/4in X 1/2in Barbed X Barbed
Connector, 3/4in X 1/2in, barbed X barbed Connects a 3/4" tube to a 1/2" tube -
Sku: 70906Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Barbed adapter which is 3/4" male threads on one end and 1/2" barbed on the other -
Sku: 301035Barbed Adapter, 432-007525
Barbed adapter -
Sku: 71263Wallfitting, Gray, without Knockout
Gray wallfitting, for Hot Spring -
This is a PVC adapter that has 1/2" male threads on one end and 3/8" barbed on the other Allows a 1/2" female fitting to be adapted to 3/8" tubing that has no fitting on the end -
Sku: 70825-BYPSnap Ring Pliers Tool, Smart Jet Diverter Valve
These snap ring ("c"-ring) pliers can be used to remove the snap ring on Smart Jet diverter valves (71494, 71495, 73768, 73769) found in most hot tubs Made of carbon steel and vinyl grip handles and comes with interchangable straight, 45 degree and 90 degree ...read more -
This is a PVC adapter that has 1/4" male threads on one end and 3/8" barbed on the other Allows a 1/4" female fitting to be adapted to 3/8" tubing that has no fitting on the end -
This barbed adapter has a 1/2" barbed fitting on one end, and a 1/2" male pipe thread fitting on the other end Then on the side of it, it has a 1/4" barbed fitting -
Sku: 30549Union, 1-1/2in Slip x Threaded
Union, 1-1/2in slip x threaded -
Sku: 71117
Wallfitting, Drain Modified
Wallfitting, drain modified -
Sku: 36581Barbed adapter 3/4 in x 1/2 Spigot
Barbed adapter 3/4 in x 1/2 spigot -
Sku: 1291501Barbed adapter 3/8 in x 3/4 Spigot
Barbed adapter 3/8 in x 3/4 spigot -
This rear wall fitting is found on the backside of the spa shell and attached to the drain plumbing It has a front wall fitting (30488) and o-ring (30482) that screws into it from the front side of the spa shell The front wall fitting has a female 1-1/2" ...read more -
Sku: 30552Adapter, Union 1-1/2in
Used on the 30215 Starite Jet pump This adapter screws into the 1 1/2" FPT fitting on the jet pump and accepts the union used on spas that use the 30215 jet pump in the early 90s This piece will only work with the original union If the union has been ...read more -
Sku: 10430Rear Venturi Wallfitting
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com Rear wallfitting for the Hydro-Air jet used in all Hot Springs models in 1990 and 1991 -
Sku: 33729Wallfitting, Pvc Rear
Obsolete: No factory suggested replacement available at this time Please contact our technicians for advice (805) 541-9000 or wizard@backyardplus com -
Sku: 33728Wallfitting, Front 1-1/2in
Obsolete: Factory replacement suggestion item #74958 and 75146 Used in the 2001-2008 Tiger River & Solana spas The suction fitting style has been updated to 2009 standards and requires the 74958 wall fitting and the 75146 or 75147 grate
Showing 1–30 of 33 results