The team at Backyardplus.com are the best for anything Hot Springs. Super friendly and knowledgeable.On 06/05/2024 by S. O. (verified customer)
Showing 1–30 of 51 results
-
Sku: 30237-x2-BYP
Compression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 32267-1
Drain Plug, Wavemaster
This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline For spas with a bleedline, the 32267 is used in place of this fitting This drain plug can be ...read more -
Sku: 301488
Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401
Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
This plug has been used on the 220volt pre-1995 Hot Spring heater to cap off the drain hose by clamping the 1/4" vinyl drain tubing to the closed 1/4" nipple on this plug Also used in the 71557-BYP Kit
-
Sku: 11080
449-020 2in Plug
This is a 2" PVC plug It can be used to plug any 2" female PVC fitting and should be installed using PVC primer and cement You can get PVC cement at your local hardware store -
Sku: 30490
Wallfitting, Rear
This fitting is used on many different Hot Spring spa models in various places including the grill style filter compartment as part of the filter assembly Also used in the filter compartment of all 1992-1996 Tiger River spa models -
This threaded wall fitting is located in the bottom of the filter compartment on all 1997-2010 Tiger River Bengal, Caspian, Sumatran & Siberian spa models This is where the filter standpipe screws into
-
Sku: 38429
Water Manifold,1in X 1/2in 4-Port
Water Manifold, 1" x 1/2" 4-port -
Sku: 34338
Manifold, Flow Cone
Manifold, flow cone -
Sku: 71128
Wallfitting, Drain Drilled
Wall fitting, rear drain, 1/2" drilled, Hot Spring Rear wall fitting located in the footwell of the spa Front wall fitting part 30488 -
Sku: 39704
6-3/4 Port Water Manifold, 2in Slip PVC
PVC water manifold, 2" Slip x 6 Port 3/4" -
Sku: 30697
Plug, 3/4in Spig
Plug, PVC, 3/4" Spig This plug is made out of PVC and fits in a female PVC slip fitting It can be used to plug an extra port on a manifold or tee that is not needed Or cap off a piece of plumbing that is no longer used -
Sku: 39702
Manifold, Water, 2in X 1/2in, 6-Port
PVC water manifold, 2" X 1/2", 6-Port -
Sku: 70906
Elbow/Union Assembly, Hot Spot
This assembly is used in two places on the 1993-1994 Hot Spot equipment compartment One of these assemblies connects onto the discharge (top) of the Wavemaster 3000 jet pump and the other end connects onto one side of the heater The second place is on the ...read more -
Sku: 300042
Manifold, 2 Port, 3/4in X 1/2in X 1/2in
Wye manifold with 3/4" slip inlet to two 1/2" slip outlets Used on Hot Spring, Tiger River, Hot Spot & Solana spa models PVC cement and primer should be used to make the connections to this manifold -
Sku: 301235
Manifold 1.5in X X 1.5in SP X (4)
Manifold, 1 5inch slip by 1 5 SP x 4 -
PVC water manifold, 1-1/2" X 1/2", 6-Port
-
Sku: 71263
Wallfitting, Gray, without Knockout
Gray wallfitting, for Hot Spring -
Sku: 1056601
8 Port Manifold, 2-1/2in x 3/4in
This is a manifold with 2-1/2" slip inlet to eight 3/4" slip outlets It can be used with rigid or flexible PVC piping or male PVC slip fittings PVC primer and cement should be used to adhere to the connections -
Sku: 010020
Four Barbed Water Manifold
Four barbed water manifold (MANIFOLD 4 BARB 1INX3/8IN) for Hot Spring, Hot Spot, and Limelight models -
Sku: 010004
Four Port Water Manifold
Four port water manifold for Hot Spring, Hot Spot and Limelight models MANIFOLD 2S/2SP/4-PORT 1/2 -
Sku: 30699
Plug, 1-1/2in Spig
This PVC fitting is used to plug 1 1/2" female PVC slip fittings It should be attached using PVC primer and cement, which is available at your local hardware store It is made out of white PVC plastic -
Sku: 30698
Plug, 1in Spig
This is a 1" PVC plug It is used to plug a 1" female PVC fitting and should be attached using PVC cement and PVC primer This will usually be used when a fitting has multiple openings, and not all of the openings are being used -
Sku: 30696
Plug 1/2in Spig
Plug, PVC, 1/2" Spig -
Sku: 10012
Manifold, 2 Port 1 S 1/2in S X 3/4in
This 2 port manifold is made of white PVC and is used to connect a 1 1/2" PVC pipe, either flexible or rigid, to two 3/4" PVC pipes, also either rigid or flexible The connections should be made using PVC primer and cement -
Sku: 010007
Manifold, 2S x 2S X 1/2″ (4) Port
Water Manifold, 2" x 2" x 1/2" 4-Port -
Sku: 010016
Manifold, 4 Port , 1-1/2″ X 3/4″
Water manifold with 1-1/2" inlet and four 3/4" outlet ports Used in various spa models within the Watkins family Use pvc primer and pvc cement when gluing either flexible or rigid pvc to this manifold -
Sku: 010018
Manifold, Water, 1-1/2″ X 3/4″ (6 Port)
This six-port manifold is made of white PVC and is used to connect a 1 1/2" PVC pipe, either flexible or rigid, to six 3/4" PVC pipes, also either rigid or flexible The connections should be made using PVC primer and cement
Showing 1–30 of 51 results