On 03/05/2024 by C. W. (verified customer)
Showing 61–90 of 234 results
-
Sku: 70059Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70036Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70396Washer, Flat 3/8in Wavemaster
Flat 3/8in washer -
Sku: 30219Volute Clamp, Starite without Nut
This stainless steel volute clamp is used to bind the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on Hot Spring spa models -
Sku: 30222Sta Rite Diffuser O-Ring
Diffuser o-ring for the 1hp & 2hp Sta-rite jet pumps used in Hot Spring models prior to 1993 -
Sku: 30297Nut, Volute Clamp, Starite
Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994 -
Sku: 70032-BYPSeal Plate Kit, Starite- After Market
This after-market (Sta-rite) seal plate is the part of the "wet end" that bolts onto the pump motor This seal plate is the replacement for both the 1hp and 2hp Starite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 Please note, the pump ...read more -
Sku: 70032-SPSeal Plate only
This after-market (Sta-rite) seal plate is the part of the "wet end" that bolts onto the pump motor This seal plate is the replacement for both the 1hp and 2hp Starite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 Note: DOES NOT INCLUDE ...read more -
Sku: 70400-BYPShaft Seal, Wavemaster 7000 (v.1)
This shaft seal is for the Wavemaster 7000 (v 1) Sta-rite 5/8" shaft seal used on the 1HP and 2HP jet pumps that were built from 1998 forward This seal is used with the seal plate that DOES NOT require the copper heater sink If you are repairing a pump ...read more -
Sku: 30224Starite Shaft Seal
Sta-rite shaft seal used on the 1HP and 2HP jet pumps that use a copper heat sink on Hot Spring spas Reference number: U109-93SS -
Sku: 70120-BYPImpeller, 2Hp Starite
After Market replacement Sta-rite impeller for the 2Hp pumps used on the Hot Spring Highlife prior to 1992 -
Sku: 30220Volute O-Ring, Starite
Volute O-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993 -
Bolt that secures the motor onto the Wavemaster 7000 (v 1) seal plate -
This bolt is used to secure the base of the 1st version Wavemaster 7000 jet pump to the motor and also secures the base to the floor of the equipment compartment -
This o-ring fits onto the front of the diffuser on the Wavemaster 7000 (v 1) jet pump and also between the suction flange and the suction cover on the front of the pump -
This heavy-duty fiberglass-reinforced polymer split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age and finally over-tightening The two halves of this fitting are held ...read more -
Largest o ring on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump seal plate -
This is the after-market 3/4" Replacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 -
Sku: 71030Shaft Seal, Wavemaster 7000 (version 2) and 9000
This item is obsolete and replaced by:
71030-BYPReplacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000 See item 71030-BYP for after-market shaft seal -
O-ring that mounts onto the front of the pump diffuser -
Sku: 70401Impeller, 1Hp Wavemaster 7000 (v.1)
Replacement impeller for the first Wavemaster 7000 used on the 1993-1996 Hot Spring Classic, 1993-1995 Grandee, Highlife and Sovereign spa models The impeller screws onto the motor shaft (right-hand threads) This impeller does not require an impeller screw -
Sku: 72349Rubber Feet, Wavemaster (Set of 4)
Rubber Mounts (feet) for the Wavemaster jet pump These are used to buffer the vibrations from the jet motor within the equipment compartment Comes in a set of four -
This replacement compression fitting split nut (AKA Split Union Nut-2") is used to connect heaters on the 1993-1994 Hot Spot Z, all 1998-current Hot Spot models, Solana models beginning in 2000 and all 1992-1994 Tiger River spas It is designed in two half ...read more -
Sku: 70039Slinger, Starite
Water slinger used on the 1HP and 2HP Sta-rite Max-E-Glas jet pump on Hot Spring spas The slinger prevents water, that may be leaking from the shaft seal, from dripping back into the windings of the electric motor and corroding that motor -
Sku: 300349Rubber Foot, Wavemaster
Used on the base of the Wavemaster 8000 (ver 3), 8200, 9000 (ver 3) and 9200 jet pump to reduce the pumps noisy vibrations being transferred to the spa shell Sold individually -
This slinger is for the Wavemaster 7000 version 2 and the Wavemaster 9000 If the pump's shaft seal was to begin leaking, the slinger would "sling" water off the shaft to prevent that water from migrating into the electric motor -
Sku: 30261O-Ring, Union, Starite
O-ring for the compression fitting union used on the 30215 Starite Jet Pump -
Sku: 72344Exhaust Hose, Wavemaster
This exhaust hose connects onto the rear of the jet pumps shroud (if equipped) to discharge hot air from the jet pump motor This method of cooling the jet pump ensures a longer lifespan of the pump's motor -
Sku: 34470Jet Pump Ring Adapter 1-1/2in X 2in
This adapter converts the jet pump 1-1/2" inlet and outlet (suction & discharge) to 2" It has threads on the inside and outside and is used on various Hot Spring, Tiger River, and Hot Spot spa models This item is most often used on the Wavemaster 3000 ...read more
Showing 61–90 of 234 results