Purchased the mother board for our 2006 hot springs Vanguard. Watched the video that Paul made in the installation. He goes over everything you need and the process along the way. Makes the task so effortless. I did the change out over a weekend and had a question. Email BackYardPlus and got a very fast response from Craig. I can’t say enough about the friendlyness, knowledge this company has. Will always be getting my parts from BackYardPlus. Saved me $$$ for sure. Again thank you Paul & Craig.On 03/21/2024 by C. S. (verified customer)
Showing 91–120 of 160 results
-
Jet pump motor for the Wavemaster 9000 version 2 Specs: HP: 2 0 Frame: 48Y Voltage: 230 Speed: 1 Amperage: 11 2 SF: 2 60 Hz: 60 Base: Plastic Reference: TPEG-WK02
-
Pump Shroud Air Vent for Wavemaster 7000 version 2 and Wavemaster 9000
-
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment
-
Sku: 70411
Tailpiece, Wavemaster 7000 (version 1)
Inside piece of the 2" compression fitting for a Wavemaster 7000 (v 1 and v 2) and a Wavemaster 9000 -
Sku: 10408
Receptacle, Jet Pump, Hot Spring
This jet pump receptacle mounts into the control box to provide an outlet to plug in the jet pump's power cord on the 1990-1996 Hot Spring Classic, Grandee, Highlife, Jetsetter, Prodigy & Sovereign spa models -
Wavemaster 7000 (v 1) suction cover (volute) is the front half of the "wet end" (suction side) It has a square flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996
-
Sku: 70407GSKT
Volute Suction Flange Gasket, Wavemaster 7000 (v.1)
Wavemaster 7000 (v 1) suction flange gasket This gasket fits between the volute cover and the square suction flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996 -
Sku: 72461
Power Cord, Wavemaster, 2-Speed
This power cord is a 14/4 (60" long) with flag terminals on both ends The cord has four wires inside which are BLACK, RED, WHITE, GREEN and is used on the two speed Wavemaster Jet Pumps -
Sku: 30225
Start Capacitor, Starite 1HP
Start capacitor used on all Sta-rite 1Hp Max-E-Glas jet pumps found on pre-1994 Hot Spring Grandee, Classic, Indoor/Outdoor, and Sovereign spa models -
Lock washer for the diffuser screw on a Wavemaster 7000 (ver 2) and Wavemaster 9000 jet pump
-
Sku: 70126
Pump Mounting Bracket, Starite 2HP
Pump mounting bracket used to secure the 2HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment -
Sku: 70031
Pump Mounting Bracket, Starite 1HP
Pump mounting bracket used to secure the 1HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment -
Sku: 35248
Wavemaster 8000 Jet Pump Power Cord
Power cord with connector used on the Wavemaster 8000 on the 1994-1996 Tiger River Khyber spa model -
Sku: 70885
Power Cord, Wavemaster 3000
1995-1997 Hot Spot spas 40" replacement power cord (cord set) for the Wavemaster 3000 Jet Pump This cord set has the correct Molex end connector to enable the Wavemaster 3000 Jet Pump to plug into the control box on all 1995-1997 Hot Spot models -
Sku: 70946
Impeller Screw, Wavemaster 9000
This stainless steel screw holds the impeller onto the Wavemaster 9000 jet pump shaft -
Flat Volute washer for the Wavemaster 7000 version 2 and he Wavemaster 9000
-
Sku: 73740
Leak Detection Kit
For Technicians Only Leak detection kit for Hot Spring, Hot Spot, and Limelight models -
Sku: Ceramic-Disk-BYP
Ceramic Pump Seal Disk
This ceramic piece is part of most pump seal kits -
Sku: 71400
Motor, 1.5Hp, XP
This is a replacement motor for a Wavemaster 5000 used on Tiger River and Hotsprings spas It can be wired 110 volts or 220 volts and is a single speed motor Will accept 48y frame wet ends -
Sku: 71401
Motor, 2.0 Hp, Wavemaster 8000 (ver. 2)
Factory replacement motor for the Wavemaster 8000 (2HP) two horsepower jet pump -
Sku: 70959
Base, Wavemaster 9000
Black plastic base that serves two purposes: The first is to support the pump & motor and the second is to secure the base to the equipment compartment floor If you have a 48 frame pump, you will need the rubber pad 70958 that inserts/sits in the plastic ...read more -
This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000, second version and a Wavemaster 9000 jet pump They are used to hold the seal plate in place against the motor
-
This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump
-
Sku: 70826
Cordset, Wavemaster 3000 Pump Hot Spot Z
This is a 12" power cord with the correct red connector, on the end, for a 1993-1994 Hot Spot Round (Z model) -
Bolt that secures the suction flange onto the front of the Wavemaster 7000 (v 1)
-
Sku: 70121
Run Capacitor, Starite 2HP
Run capacitor used on all 2HP Starite Max-E-Glas jet pumps on Hot Spring spas -
Sku: 30549
Union, 1-1/2in Slip x Threaded
Union, 1-1/2in slip x threaded -
This screw is used to secure the volute to the pump base 70959
-
Sku: 70958
Rubber Motor Pad, Wavemaster 9000
Rubber pad between the motor and the base to keep vibrations to a minimum It's used with item 70959 plastic pump base If you use a 48 frame pump, you need this rubber pad to fill the gap that is left between the motor and the base If you have a 56 frame ...read more -
One of two volute washers on the Wavemaster 7000 (second version) and the Wavemaster 9000 jet pump
Showing 91–120 of 160 results