It was easy to get someone on the phone and they were very helpful with advice on parts and installation. Will definitely buy from in the future.On 01/10/2024 by C. R. (verified customer)
Brand: Hot Spring Pre 89, Starite
Showing 91–120 of 192 results
-
Sku: 30261O-Ring, Union, Starite
O-ring for the compression fitting union used on the 30215 Starite Jet Pump -
Sku: 72344Exhaust Hose, Wavemaster
This exhaust hose connects onto the rear of the jet pumps shroud (if equipped) to discharge hot air from the jet pump motor This method of cooling the jet pump ensures a longer lifespan of the pump's motor -
Used to convert 1/2" plumbing to 3/4" on pre-1990 Hot Springs only This kit contains all the fittings & tubing necessary to convert your 1/2" plumbing to 3/4" when replacing the older style 1/2" inlet/outlet Hot Spring circulating pumps to the new ...read more -
Sku: 72072-1.5Split Nut for 1.5in Compression Fittings
This 1-1/2" split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age, and over-tightening The two halves of this fitting are held together by two screws -
The diffuser mounts onto the seal plate of the Wavemaster 7000 second version and the Wavemaster 9000 jet pump using seven stainless steel screws -
This 48" power cord w/square plug is for all single speed circulation pumps (Silentflo 5000) on all 1989-1996 Hot Spring spa models For a two-speed circulation pump (Silentflo 5002) power cord use the four-wire power cord 34948 -
Volute for the Wavemaster 7000 version 2 and the Wavemaster 9000 v 1 -
Sku: 30221Diffuser, Starite
Sta-rite Diffuser used on the 1HP and 2HP Max-E-Glas jet pumps on Hot Spring spa models -
Sku: 30221-BYPDiffuser, Starite- After Market
After-market Sta-rite Diffuser used on the 1HP and 2HP Max-E-Glas jet pumps on Hot Spring spa models -
This pad goes between the motor base and the plastic base buffer against noisy motor vibrations -
Impeller screw for the Wavemaster 7000 (v 1) This screw is reversed thread (left hand thread) This screw is not needed if you are purchasing a new impeller 2014 forward -
Sku: 70408Diffuser, Wavemaster 7000 (v.1)
The diffuser screws onto the seal plate of the Wavemaster 7000 (v 1) with 3 screws which are included -
Sku: 71028Rubber Pad, Wavemaster 7000 (ver. 2)
This rubber pad fits in between the motor and the steel base on the Wavemaster 7000 (version 2) and provides a buffer against vibrations This is one of two rubber pads that mount on the steel base The second is under the base between the base and the floor ...read more -
Sku: 70945Gasket, Impeller Screw Wavemaster 9000
This little gasket fits over the impeller screw and is snugged into place against the impeller when the screw is tightened -
Sku: 30548Starite Compression Fitting, 1-1/2″
1-1/2" compression coupling assembly (pump union) for all Starite pumps used on Hot Spring spas -
Impeller for the Wavemaster 9000 jet pump This 2 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads -
Sku: 71434Power Cord, Silentflo
Replacement power cord for the Silentflo 5000 and the new E5 circulation pump when used on all Hot Spring, Tiger River & Limelight spas This cord has flag terminals at one end that slide onto the spades inside the IQ 2000 and IQ 2020 control boxes This ...read more -
This stainless steel impeller screw (left-hand threads) screws onto the end of the motor shaft to secure the impeller from spinning off of the Sta-rite Maxi-Glass 1hp & 2hp pumps that were used in Hot Spring spas prior to 1994 -
Sku: 70399Seal Plate, Wavemaster 7000 (v.1)
The seal plate is the half of the "wet end" on the 1st version Wavemaster 7000 that bolts onto the pump motor -
Mounts in the control box on all Hot Spring models prior to 1997 that used a square receptacle The one-speed circulation pump (Silentflo 5000) plugs into this receptacle regardless of the voltage of your spa model All Hot Spring spa circulating pumps are ...read more -
Seal Plate for the Wavemaster 7000 version 2 and the Wavemaster 9000 -
Jet pump motor for the Wavemaster 7000 version 2 Specs: HP: 1 0 Frame: 48Y Voltage: 115/230 Speed: 1 Amperage: 7 0/14 0 SF: 1 65 Hz: 60 Base: Steel Reference: TPEE-WK03 -
Jet pump motor for the Wavemaster 9000 version 2 Specs: HP: 2 0 Frame: 48Y Voltage: 230 Speed: 1 Amperage: 11 2 SF: 2 60 Hz: 60 Base: Plastic Reference: TPEG-WK02 -
Pump Shroud Air Vent for Wavemaster 7000 version 2 and Wavemaster 9000 -
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment -
Sku: 2317Screw, #10 x 1/2″
Stainless steel screw -
Sku: 30347Screw, #10-24 X 1/2in Stainless Steel
Stainless steel screw -
Sku: 70411Tailpiece, Wavemaster 7000 (version 1)
Inside piece of the 2" compression fitting for a Wavemaster 7000 (v 1 and v 2) and a Wavemaster 9000 -
Sku: 10408Receptacle, Jet Pump, Hot Spring
This jet pump receptacle mounts into the control box to provide an outlet to plug in the jet pump's power cord on the 1990-1996 Hot Spring Classic, Grandee, Highlife, Jetsetter, Prodigy & Sovereign spa models -
Sku: 70407GSKTVolute Suction Flange Gasket, Wavemaster 7000 (v.1)
Wavemaster 7000 (v 1) suction flange gasket This gasket fits between the volute cover and the square suction flange that accepts the adapter to connect to the plumbing of the spa Used on Hot Springs spas from 1993 to 1996
Showing 91–120 of 192 results