Got what I ordered in the time advertised. Both excellent.On 01/11/2024 by C. J. (verified customer)
Showing 91–120 of 330 results
-
Sku: 30237-x2-BYP
Compression Fitting O-ring, for 1-1/2 inch Union (Qty. of 2)
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more -
1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump No Teflon tape is needed for the jet pump ...read more
-
Sku: 71038
Compression Fitting, 1-1/2in with O-Ring
This 1-1/2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling It is found on the suction and/or discharge side of FMHP/CP Series Wavemaster® Jet Pumps 2" x 1-1/2" Compression Fitting click ...read more -
This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling 1-1/2" Compression Fitting 2" Compression Fitting
-
Sku: 32267-1
Drain Plug, Wavemaster
This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline For spas with a bleedline, the 32267 is used in place of this fitting This drain plug can be ...read more -
Sku: 301488
Sweep Pump Union, 2in Soc. 90 Degree
Two-inch SOC 90deg sweep pump union -
Sku: 1119401
Pump Union, 45 Degree
Pump union (aka compression fitting) can be used to connect to any Wavemaster pump later than 1996 This union accepts a 2" PVC pipe and will attach to a 2" standard pump thread The fitting for the pipe is at a 45-degree angle -
Sku: 30018
Mounting Bolt, Wavemaster
1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000 3 jet pumps -
Sku: 30413
Mounting Bolt Washer, Wavemaster
Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment 5/16" -
Sku: 72462-BYP
Power Cord, After-Market, 1-Speed, 60″
This power cord is a 14/3 (60" long) with flag terminals on both ends The cord has three wires inside which are BLACK, WHITE, GREEN, and is used on the one-speed Jet Pumps -
Sku: 72461-BYP
Power Cord, After-Market, 2-Speed, 60″
This power cord is a 14/4 (60" long) with flag terminals on both ends The cord has four wires inside which are BLACK, RED, WHITE, GREEN and is used on the two speed Jet Pumps -
Sku: ML-1OZ-BYP
Silicone Grease, 1 oz. Tube
Silicone grease ideal for lubricating o-rings -
This after-market impeller is used on the after-market Wavemaster 9000 (ver 2), 9000 (ver 3) and Wavemaster 9200 jet pumps This 2 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads
-
This after-market impeller is used on the after-market 2 0 HP Wavemaster jet pumps This impeller screws onto the pump motor's threaded shaft with regular right-hand threads
-
This after-market impeller is used on the after-market Wavemaster 5000 and 6000 jet pumps This 1 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads
-
Sku: 71409-E
XP2E Wear Ring
This is the XP2E wear ring for the after-market impellers 71406-SW, 71405-SB and 71404-SY Please check the dots at the end of your impeller Item 71406-SW (Silver, White), item 71405-SB (Silver, Blue) and item 71404-SY (Silver, Yellow) -
Sku: 30215-Motor-BYP
1HP Starite Energy Effiecient Motor
The is the energy efficient replacement motor for the 1hp Sta-Rite pump used in some pre-1994 Hot Spring spas This motor was discontinued by Hot Spring and comes from another vendor -
Sku: 31239-Motor-BYP
Motor Only, Sta-rite 2hp
This motor replaces the two horsepower single speed energy efficient motor used on the 2HP Sta-Rite pump found on the 1989-1993 Hot Spring Highlife The "wet end" only your existing pump can be installed on this replacement motor If you require the entire ...read more -
Sku: 36070-Motor-BYP
Motor, 1HP, 36070 Pump
This electric motor is the energy efficient replacement motor for the Wavemaster 7000 (v 1) jet pump used on the 1993-1996 Hot Spring Classic, 1993-1995 Hot Spring Grandee and Sovereign spa models -
This is the largest o ring on the Wavemaster 7000 (v 1) jet pump It fits between the cover and the seal plate
-
Sku: 30217
Volute, Starite
This Sta-rite volute is the front part of the "wet end" of the 1HP and 2HP Max-E-Glas jet pumps used on the Hot Spring spa models prior to 1993 -
Sku: 30223
Impeller, 1Hp Starite
Impeller for the 1hp Sta-rite used in Hot Spring spas prior to 1993 -
Sku: 70035
Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite
Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment -
Sku: 70059
Bolt, #3/8in-16 X 1in Hex, Starite
Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps -
Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps used on Hot Spring models prior to 1993
-
Sku: 70036
Diffuser Screw, #8-32 X 7/8in, Starite
Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993 -
Sku: 70396
Washer, Flat 3/8in Wavemaster
Flat 3/8in washer
Showing 91–120 of 330 results