LOVE backyard plus, such an amazing company. Customer service is great, its so easy to find parts and get the right one! Plus prices are very competitive. Only place im every going to for hottub parts.On 10/02/2023 by K. M. (verified customer)
Showing 151–180 of 329 results
-
Used to convert 1/2" plumbing to 3/4" on pre-1990 Hot Springs only This kit contains all the fittings & tubing necessary to convert your 1/2" plumbing to 3/4" when replacing the older style 1/2" inlet/outlet Hot Spring circulating pumps to the new ...read more
-
Sku: 72072-1.5
Split Nut for 1.5in Compression Fittings
This 1-1/2" split nut comes in two pieces and is designed to replace compression fitting nuts (aka pump union nuts) that have broken due to vibration, age, and over-tightening The two halves of this fitting are held together by two screws -
The diffuser mounts onto the seal plate of the Wavemaster 7000 second version and the Wavemaster 9000 jet pump using seven stainless steel screws
-
This 48" power cord w/square plug is for all single speed circulation pumps (Silentflo 5000) on all 1989-1996 Hot Spring spa models For a two-speed circulation pump (Silentflo 5002) power cord use the four-wire power cord 34948
-
Volute for the Wavemaster 7000 version 2 and the Wavemaster 9000 v 1
-
Sku: 30221
Diffuser, Starite
Sta-rite Diffuser used on the 1HP and 2HP Max-E-Glas jet pumps on Hot Spring spa models -
Sku: 30221-BYP
Diffuser, Starite- After Market
After-market Sta-rite Diffuser used on the 1HP and 2HP Max-E-Glas jet pumps on Hot Spring spa models -
This pad goes between the motor base and the plastic base buffer against noisy motor vibrations
-
Impeller screw for the Wavemaster 7000 (v 1) This screw is reversed thread (left hand thread) This screw is not needed if you are purchasing a new impeller 2014 forward
-
Sku: 70408
Diffuser, Wavemaster 7000 (v.1)
The diffuser screws onto the seal plate of the Wavemaster 7000 (v 1) with 3 screws which are included -
Sku: 71028
Rubber Pad, Wavemaster 7000 (ver. 2)
This rubber pad fits in between the motor and the steel base on the Wavemaster 7000 (version 2) and provides a buffer against vibrations This is one of two rubber pads that mount on the steel base The second is under the base between the base and the floor ...read more -
Sku: 70945
Gasket, Impeller Screw Wavemaster 9000
This little gasket fits over the impeller screw and is snugged into place against the impeller when the screw is tightened -
Sku: 30548
Starite Compression Fitting, 1-1/2″
1-1/2" compression coupling assembly (pump union) for all Starite pumps used on Hot Spring spas -
Impeller for the Wavemaster 9000 jet pump This 2 5 HP impeller screws onto the pump motor's threaded shaft with regular right-hand threads
-
Sku: 71434
Power Cord, Silentflo
Replacement power cord for the Silentflo 5000 and the new E5 circulation pump when used on all Hot Spring, Tiger River & Limelight spas This cord has flag terminals at one end that slide onto the spades inside the IQ 2000 and IQ 2020 control boxes This ...read more -
Sku: 34416
Pump Check Valve, Umbrella, Tiger River
This red-colored umbrella check valve is found inside the 71368 used on the discharge (top) of the 1994-1996 Tiger River spas Wavemaster Jet Pump This check valve ensures that when the jet pump is off that the Silentflo 5000 circ pump pulls water from the ...read more -
This stainless steel impeller screw (left-hand threads) screws onto the end of the motor shaft to secure the impeller from spinning off of the Sta-rite Maxi-Glass 1hp & 2hp pumps that were used in Hot Spring spas prior to 1994
-
Sku: 70399
Seal Plate, Wavemaster 7000 (v.1)
The seal plate is the half of the "wet end" on the 1st version Wavemaster 7000 that bolts onto the pump motor -
This compression fitting (aka pump union, quick disconnect, coupling) is used on the discharge side of the Tiger River Wavemaster Pumps to ensure that the small Silentflo 5000 or 5002 circulation pump pulls water through the filter when the jet pump is off ...read more
-
Mounts in the control box on all Hot Spring models prior to 1997 that used a square receptacle The one-speed circulation pump (Silentflo 5000) plugs into this receptacle regardless of the voltage of your spa model All Hot Spring spa circulating pumps are ...read more
-
Seal Plate for the Wavemaster 7000 version 2 and the Wavemaster 9000
-
Jet pump motor for the Wavemaster 7000 version 2 Specs: HP: 1 0 Frame: 48Y Voltage: 115/230 Speed: 1 Amperage: 7 0/14 0 SF: 1 65 Hz: 60 Base: Steel Reference: TPEE-WK03
-
Jet pump motor for the Wavemaster 9000 version 2 Specs: HP: 2 0 Frame: 48Y Voltage: 230 Speed: 1 Amperage: 11 2 SF: 2 60 Hz: 60 Base: Plastic Reference: TPEG-WK02
-
Pump Shroud Air Vent for Wavemaster 7000 version 2 and Wavemaster 9000
-
Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment
-
Sku: 2317
Screw, #10 x 1/2″
Stainless steel screw -
Sku: 30347
Screw, #10-24 X 1/2in Stainless Steel
Stainless steel screw -
Sku: 70411
Tailpiece, Wavemaster 7000 (version 1)
Inside piece of the 2" compression fitting for a Wavemaster 7000 (v 1 and v 2) and a Wavemaster 9000 -
Sku: 33292
Jet Pump Cordset, Tiger River
14/3 X 48" power cord with the correct connector for the 1992-1994 Tiger River Khyber, Manora and Tondi spa models -
Sku: 10408
Receptacle, Jet Pump, Hot Spring
This jet pump receptacle mounts into the control box to provide an outlet to plug in the jet pump's power cord on the 1990-1996 Hot Spring Classic, Grandee, Highlife, Jetsetter, Prodigy & Sovereign spa models
Showing 151–180 of 329 results