After-Market, Impeller, Wavemaster 5000/6000, 1.5HP, Silver, Yellow

Item #: 71404-SY
$34.13

This after-market impeller is used on the after-market Wavemaster 5000 and 6000 jet pumps. This 1.5 HP impeller screws onto the pump motor’s threaded shaft with regular right-hand threads.

SKU: 71404-SY Categories: , Tag:

Description

Description: This after-market impeller is used on the after-market Wavemaster 5000 and 6000 jet pumps. This 1.5 HP impeller screws onto the pump motor’s threaded shaft with regular right-hand threads.

Installation: The steps to replace an impeller are very similar to replacing a wet-end kit and take about the same amount of time.
Step 1. Unscrew and Remove the volute cover of the Wet End.
Step 2. Use a pair of plyers to hold the motor shaft while you turn the impeller counterclockwise.
Step 3. Turn the impeller counterclockwise until it is free from the motor shaft.
Step 4. If the spring-loaded part of the shaft seal, or the wear ring are still on the impeller, remove them.
Step 5. To install the new impeller, simply reverse steps 1 – 4.

Please check the vendor code or pump model on your pump before ordering replacement parts and use the chart to determine the correct impeller replacement. If your vendor code reads “3536”, see item IMP-77710 for the impeller replacement or 77710 for the complete wet-end replacement. If your vendor code is “3861”, please call 805-541-9000 or text us photos of your pump’s labels.

This impeller will work on the following wet-end kits:
Wet End Impeller Shaft Seal Wear Ring
72993-BYP* 71404-SY** 71447-BYP 71409-E

*Wet-end label: 91041815-000; Stamped on wet end leg: 92770705; Stamped on volute cover: 91231605. If your wet end has been changed in the past and there is a label/sticker that reads 91041609-020-001, use 71404.
**71404-SW Dots: silver, yellow(use 71409-E wear ring)
If you can’t determine the dots on your impeller, buy the entire wet-end kit. The installation time is about the same.

View Diagrams & Part Compatibility

You may also like…

  • Volute O-Ring, Wavemaster
    This is the largest O-ring used on the current Wavemaster series of wet ends for Hot Springs, Tiger River, Limelight, Solana and Hot Spot model spas This o-ring fits between the suction cover and the volute of the pump series: XP2/XP2E This o-ring is only ...read more
    $13.46
    Add to cart
  • Wet End Kit, After-Market, Wavemaster 5000 1.5HP
    This is the after-market "wet end" is for the Wavemaster® 5000 1 5HP pump that was used on the 1997-2000 Hot Spring Jetsetter, 1997-2000 Tiger River Sumatran and 1997 Tiger River Bengal spa models Also included is the bleedline nipple (item 32267) Please ...read more
    $120.07 View OEM
    Add to cart
  • Shaft Seal Kit, Wavemaster
    The shaft seal kit is used to prevent water from leaking from around the rotating pump shaft This seal kit is used on most of the Wavemaster and after-market jet pumps Please find your pump model number and if your pump is an OEM Wavemaster, you will also ...read more
    $19.30
    Add to cart
  • Wear Ring, Wavemaster
    This is the XP2E wear ring for the after-market impellers 71406-SW, 71405-SB and 71404-SY Please check the dots at the end of your impeller Item 71406-SW (Silver, White), item 71405-SB (Silver, Blue) and item 71404-SY (Silver, Yellow)
    $7.11
    Add to cart